Lahara Single Handle Lavatory Faucet with Touch2O.xt&trade; Technology

0points

0out of 0found this question helpful.

Was this helpful?helpful0unhelpful0

Answer:

Thank you for your question. Delta Faucet model # 538T-DST has a spout that is all one peice with the handle being a separate peice.

Skill Level: Advanced

6 months ago

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0

on Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

Has staff answer

Has expert answer

Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

3 answers

Why is hot water flow very faint?

MarkSloan

Lines do not appear to be pinched, yet the hot water flow is very faint...just a small drizzle. Setting on the faucet is on 1 and the handle goes all the way to the left, but the flow is no where near how it is for the cold water.

Topics: Performance, Assembly

5 months, 2 weeks ago

MarkSloan

0points

0out of 0found this question helpful.

Was this helpful?helpful0unhelpful0

Answers

Number one contributor
Social Answering Subscriber

Answer:

I would remove the hot water line from the valve underneath and flush it out....should solve problem...if not, have a plumber look at it for you.

Age: 35 to 44

Gender: Male

5 months, 1 week ago

ilovemyducks67

Roseburg, OR, USA

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0

Staff
Expert

Answer:

Thank you for your question. I apologize for the issue that you are experiencing. To ensure the proper part is identified for repair, please contact our toll-free Home Owner/Warranty department at 800-345-3358.

Skill Level: Advanced

5 months, 1 week ago

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0

Answer:

As a follow up to my own question: I purchased two of these models and tried switching parts around to narrow the problem, but that didn't help. On a hunch, I took the shut-off valve apart and discovered that the little rubber gasket on the end of the shut-off valve handle had deteriorated and was blocking part of the valve opening. I replaced the gasket and the faucet worked perfectly.

When I installed the second unit, the identical same thing happened! However, I knew what to do this time! Sure enough, the gasket on it was blocking the inlet flow as well. The simple act of opening and closing the shut-off valve will eventually wear this gasket.

Thanks to the person who responded earlier and mentioned about checking the plumbing, because that was exactly the problem. Both units are working perfectly now.

5 months ago

MarkSloan

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0

on Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

Has staff answer

Has expert answer

Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

1 answer

Hands Free Mode is not working

Doug

I see there is a way to disable Hands Free mode, is there a way to re-enable it?

I was doing some work under my sink and now Hands Free mode is not working, I am thinking I must have disabled Hands Free mode by mistake while working.

6 months ago

Doug

0points

0out of 0found this question helpful.

Was this helpful?helpful0unhelpful0

Answers

Staff
Expert

Answer:

Skill Level: Advanced

6 months ago

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0

on Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

Has staff answer

Has expert answer

Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

1 answer

Is there a way to adjust the motion sensitivity of this faucet?

Sean

I would like to extend the motion sensitivity of the faucet by a couple of inches. The water shuts off when people are soaping their hands and then takes a couple more waves of the hand (sometimes more) to get it flowing again.

If the proximity can't be adjusted, can the motion sense be shut off completely so it becomes a touch faucet?

thanks!

Topics: Features, Performance, Care/Maintenance

Skill Level: Intermediate

7 months ago

Sean

0points

0out of 0found this question helpful.

Was this helpful?helpful0unhelpful0

3I have this question too

Answers

Staff
Expert

Answer:

Thank you for your question. Delta Faucet model # 538T-SS-DST is equipped with touch free and a hands free mode. The proximity cannot be adjusted and is 3 inches from the spout. If someone soaping their hands removes their hands from the zone, the water will turn off.

If you would like to de-activate the hands-free mode, please follow these instructions:
1) Tap the spout 6 times within 4 seconds.
2) the LED indicator light will flash red/blue.
3) Tap the spout an additional 6 times within 4 seconds of the flashing red/blue LED indicator light.
4) The LED indicator light will flash red/blue a second time to indicate the hands-free mode has been de-activated.
5) The tapping sequence can be done with the handle in the ON or OFF position.

Skill Level: Advanced

7 months ago

-1point

1out of 3found this answer helpful.

Was this helpful?helpful1unhelpful2

on Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

Has staff answer

Has expert answer

Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

1 answer

How do I get this faucet tightened down to the sink?

Quapawpers

Little Rock

Seems that no matter how hard I turn the tool to tighten the nut, that the faucet keeps slipping on the sink. I'm afraid of breaking the plastic tool that came with the faucet; and afraid that if I try to use a regular wrench that I'll break something else. Help!

Topics: Assembly

Age: 55 to 64

Gender: Male

Project Type: Replacement

Ownership: < 1 year

Skill Level: Intermediate

10 months ago

Quapawpers

Little Rock

0points

0out of 0found this question helpful.

Was this helpful?helpful0unhelpful0

Answers

Staff
Expert

Answer:

Skill Level: Advanced

10 months ago

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0

on Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

Has staff answer

Has expert answer

Lahara Single Handle Lavatory Faucet with Touch2O.xt™ Technology

3 answers

Is there a part/tool to connect the input hose to the output hose to bypass the solenoid unit?

JMSchneid

Louisville, KY, USA

Topics: Care/Maintenance

Age: 65 or over

Gender: Male

Project Type: Replacement

Ownership: < 1 year

Skill Level: Advanced

9 months ago

JMSchneid

Louisville, KY, USA

0points

0out of 0found this question helpful.

Was this helpful?helpful0unhelpful0

Answers

Number one contributor
Social Answering Subscriber

Answer:

no...water needs to go through the solenoid to work properly.

Age: 35 to 44

Gender: Male

9 months ago

ilovemyducks67

Roseburg, OR, USA

-1point

0out of 1found this answer helpful.

Was this helpful?helpful0unhelpful1

Answer:

To clarify, when the solenoid unit is not working properly, is there a tool/part to connect the input hose to the output hose. This would allow the faucet to be used while waiting for parts.

When posing the original question, I thought this would be answered by Delta support.

Age: 65 or over

Gender: Male

Project Type: Replacement

Ownership: < 1 year

Skill Level: Advanced

9 months ago

JMSchneid

Louisville, KY, USA

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0

Staff
Expert

Answer:

Thank you for your question. Delta Faucet model #538T-SS-DST has a solenoid that is not recommended to be bypassed. You can put the faucet in manual mode by making sure that water is running and then disconnect the battery pack. It will then run in manual mode. If you are having issues with your faucet, please contact our Home Owner/Warranty line at 800-345-3358.

Skill Level: Advanced

8 months ago

0points

0out of 0found this answer helpful.

Was this helpful?helpful0unhelpful0