Delta 3 / 6-Setting Diverter Rough

Model #:R11000

What does this model number mean?

List Price as
Shown (US $):1
$106.15
Where to Buy

Own this product?

Registering it helps us provide the best service.

Want to save this product so you can quickly find it later?

You own this product.

I don't own this product

Need help with your product?

Troubleshoot Your Issue

Product Features and Benefits

  • 3-port, 6-setting diverter with 3 individual and 3 shared positions
  • 2-port, 3-setting diverter with 2 individual and 1 shared position
  • 1/2" universal inlets/outlets
  • Cartridge ships with trim
  • Lifetime Faucet and Finish Warranty

Product Support, Repair Parts & Tech Specs

Support Information:

Installation Instructions / Owner's Manual

Reviews

Rated 4.3 out of 5 by 10 reviewers.
Rated 1 out of 5 by Good luck If you install this valve the way the rough in tells you too, you will be very disappointed. Our valve trimmed out perfect and this transfer valve was to far back in the wall. And of course they don't make an extension for this. We had to cut open a tile wall on the other side of the valve to offset this valve above the shower valve causing us to look bad. Also install the cartridge at rough, good luck trying to remove the bonnet nut when it is an 1/8 inch behind the finished wall. January 17, 2013
Rated 4 out of 5 by Love the diverter We recently remodeled the master bath and opted for a handheld shower and rain can in our walk-in shower. The diverter allows us to use either or both. Highly recommend a diverter when remodeling a bath with shower. May 3, 2013
Rated 5 out of 5 by Smooth Valve We coupled this with the Delta T11800 chrome trim package and the valve delivers good pressure and finger tip selection between our Delta 57014 Hand Shower Package and Delta T17230-H2O Classic Shower Trim Package with H2Okinetic, Independent Volume Control and Monitor Technologies. Was even surprised at the pressure delivered in the mix position supplying water to both shower heads. April 1, 2013
Rated 5 out of 5 by Great service. Way better than expected even I ordered few faucets for a remodel. Delivered quicker than expected. Had problem with one of them and still can't believe how quickly they took care of it. Thought I would wind up in internet no mans land. They emailed me back with 20 minutes and the replacement part was in the mail to me the same day. Received it two days later. September 14, 2014
Rated 5 out of 5 by Good valve Great Find. If you are looking for diverter valve this is the one you need. This thing is well priced and really solves your diverted issue. This one comes with a plug to cover one port. January 1, 2011
Rated 5 out of 5 by excellent choice This product comes in 3 or 6 way diverter types. We chose the 6 way. it works great. very smooth operation. precision machined piece where everything fit together snugly. April 19, 2011
Rated 5 out of 5 by Excellent Product Purchased as part of a shower remodel. All other components were Moen, but Moen did not have needed 6way diverter. This Delta product was recommended and works great.... May 8, 2011
Rated 3 out of 5 by does not show to the eye makes no difference since valve is installed inside the wall. Cannot recommend since it comes with the other parts. September 13, 2015
  • 2016-02-06 T03:16:09.730-06:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_10, tr_10
  • loc_en_US, sid_R11000, prod, sort_default
From time to time, Delta Faucet Company runs sweepstakes in connection with its Ratings and Reviews. Certain of the reviews posted above on this page may have entitled the author to a sweepstakes entry.

Customer Q & A

(42 Questions : 48 Answers)

Product Q&A

Ask your questions. Share your answers.

 
 
« Back
 
 
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

WHAT DO I NEED ??

I plan on having a rainfall shower head as well as a wall mount shower and a hand held sprayer.....
Will the Delta 3/6 setting diverter allow me to mix to functions of to features or use them alone ?
If not what do I need ?
Topics: Features
Age: 45 to 54
Gender: Male
Project Type: New
Ownership: < 1 year
Skill Level: Beginner
1 week, 2 days ago
Customer avatar
by
RWB1
NEW YORK
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi RWB1,

Thank you for your question! Along with a 6-Setting Diverter Trim Kit, this valve will allow you to run each component individually or paired with another component.

Best regards,
Jon
1 week, 1 day ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet3 is loaded.
Additional information about DeltaFaucet3 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

will the 3/6-setting diverter valve allow me to use a hand held shower, regular fixed head and a rain head independantly?

Customer avatar
by
Al
Gordon, Georgia
I do not want to use any of these at the same time.
Age: 65 or over
Gender: Male
2 weeks, 5 days ago
Customer avatar
by
Al
Gordon, Georgia
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Al,

Thank you for your question!

When using the R11000 diverter valve with 3 separate items you need to install a 6 setting diverter trim kit. This will allow you to use any of the 3 items independently and any 2 items mixed together. The below link will have a list of our 6 setting diverter trims.

http://www.deltafaucet.com/search/r...

Best Regards,
Daniel
2 weeks, 3 days ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about Delta5 is loaded.
Additional information about Delta5 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

do you have a tool to remove the bonnet nut?

Topics: Assembly
1 month, 1 week ago
Customer avatar
by
cory
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Cory,

Thank you for your question! We recommend to use a strap wrench if it does not come off by hand.

Best regards,
Jon
1 month, 1 week ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet3 is loaded.
Additional information about DeltaFaucet3 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

can a shower diverter be put into a 2 1/2 inch wall?

Age: 55 to 64
Project Type: New
Skill Level: Advanced
1 month, 1 week ago
Customer avatar
by
Joe
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Joe,

Thank you for your question. The back of the valve must be 2 3/4" from the finished wall. This would mean that the valve and piping would need to fit within the hole of the wall using elbows. A standard diverter trim escutcheon plate is 4 1/2". If you can work around these specifications, it should work. Please click the links below for more details.

http://www.deltafaucet.com/customer...

http://www.deltafaucet.com/customer...

Best regards,
Jon
1 month, 1 week ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet3 is loaded.
Additional information about DeltaFaucet3 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

I have a valve and shower head, rain can, hand held and 4 body sprays (2 sprays in one location and 2 sprays in another.)

Customer avatar
by
Lori Corcoran
Tampa, Florida
how many diverters and valve do I need i thought I would need just one 6 setting diverter but I am being told that will not work
4 months, 1 week ago
Customer avatar
by
Lori Corcoran
Tampa, Florida
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Lori,

Thank you for your question. With the setup you are looking for, you will need two R10000 valves and trim, and two R11000 valves and trim. We recommend to use no more than 3 body sprays on one port of the diverter. In this case you will need one 3 setting diverter and one 6 setting diverter trim to operate the shower head, rain can, handshower, and two sets of body sprays.

Thanks,
Jon
4 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet3 is loaded.
Additional information about DeltaFaucet3 could not be loaded.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

Pex between universal valve and 3/6 diverter ok?

Customer avatar
by
Becca
Phoenixville, PA, USA
My system is PEX. Hand shower & rainhead installation. I'm roughing in the universal valve and 3/6 diverter. Instructions say to sweat copper from universal valve top outlet to bottom inlet on diverter. Is there any reason I cannot use PEX for this connection? I understand the reasons for using copper between valve and a tub spout in a tub shower combination, but this is shower only. Side question, the supplied brass plug on the diverter is meant to be sweated in, correct? Thanks!
Topics: Assembly, rough in
Age: 35 to 44
Gender: Female
Project Type: New
Skill Level: Advanced
5 months ago
Customer avatar
by
Becca
Phoenixville, PA, USA
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Becca,

Thank you for your questions! You may use PEX tubing between the R10000 and R11000 valves. The cap is designed to be sweat into the right port of the valve for 3 setting applications.

Thanks,
Jon
4 months, 4 weeks ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet3 is loaded.
Additional information about DeltaFaucet3 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

Is R11000 legal in California?

Customer avatar
by
Prohor
Orange County, CA, USA
Building code in Southern California now allows only one showerhead to be on at a time. Can R11000 be used? What other diverter valves do you offer that are ok in California? I plan to have only 2 showerheads.
Thank you very much,
Prohor
Topics: Features
Age: 45 to 54
Gender: Male
6 months ago
Customer avatar
by
Prohor
Orange County, CA, USA
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi Prohor,

Thank you for your question! You can use the R11000 rough-in valve with a non-shared cartridge to eliminate the shared setting. The 2-Function Non-Shared Diverter Cartridge is RP71717, which can be used with a 3-setting diverter trim.

http://www.deltafaucet.com/repairpa...

Thanks,
Jon
6 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet3 is loaded.
Additional information about DeltaFaucet3 could not be loaded.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

using R11000 with R10000

I am watching my plumber install, and I don't think he's doing it right. Using pex, he plumbed the 12oclock port directly to the rainhead. Shouldn't the diverter be in between the 2? There is also a handheld and 2 body sprays. How should these be plumbed and do you need to loop the sprays with the pex? Can you use pex for all of it? Lastly, will this valve supply enough water to the 9" rainhead?
Topics: Assembly
7 months ago
Customer avatar
by
riobella
NJ
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi riobella,

Thank you for your questions! The top port of the R10000 valve should be plumbed into the bottom port of the R11000. From there, you can use any of the remaining 3 ports of the R11000 for your shower head, handheld, or body sprays. A set of two body sprays will not require a pressure balancing loop. PEX tubing can be used for any of the plumbing, except to a tub spout (if applicable).

The amount of water flow you will get from the valves will depend on the pressure in the home as well as the trim kit you choose for the R10000 valve. However, with 60 or more PSI, there should be be enough flow to run a 2.5 GPM raincan shower head as well as shared diverter functions.

Thanks,
Jon
7 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet3 is loaded.
Additional information about DeltaFaucet3 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

How to plumb the R11000 rough in with a rain shower head, handheld and tub fill

I have the T14486-SHQ and I'm also installing the 55530 wall mount handshower. I purchased the R11000 diverter. Can you explain the correct way to install in order to allow me to switch between the overhead shower, handheld and tub fill? Thanks
Topics: Assembly
Age: 35 to 44
Gender: Male
Project Type: New
Ownership: < 1 year
Skill Level: Intermediate
8 months ago
Customer avatar
by
Ki@m
Barbados
+1point
1out of 1found this question helpful.
Was this helpful?helpful1unhelpful0

Answers

Answer: 
Hi Ki@m, Thank you for your question. The tub spout that comes with the model T14486-SHQ is a diverter tub spout. Using that tub spout you would cap the right side or 3 o-clock port on the R11000 diverter rough and plumb the rain shower head out of the 12 o-clock port and the hand shower from the 9 o-clock port. The shower port from the R10000 faucet rough would be plumbed to the 6 o-clock port on the R11000 diverter rough. The T11886 diverter trim will allow you to operate each showerhead individually or both at the same time.
Thanks,
Dave
Skill Level: Advanced
8 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet2 is loaded.
Additional information about DeltaFaucet2 could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
Has expert answer
Delta 3 / 6-Setting Diverter Rough
 
1 answer

Shower head combo

Customer avatar
by
DIY Brian
Long Island, New York, USA
Hi,
I've replace our bathtub with a shower only and I would like to install a main shower head/wand combo (584-70-SS, In2ition) and a rain shower head (T17253-SS kit). I want the ability to run them separately or together. I already purchase the T17253-SS the 584-70-SS which came with no trim) and a R10000-UNBX rough in valve, I am not sure what else I need? Please let me know what other products I need to purchase and also a little guidance as to the plumbing from valve to both shower heads.
Thanks
Topics: Purchase, Assembly
Age: 55 to 64
Gender: Male
Project Type: New
Skill Level: Intermediate
8 months ago
Customer avatar
by
DIY Brian
Long Island, New York, USA
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Answer: 
Hi DIY Brian, Thank you for your question. You will want to order the R11000 diverter rough and the T11853-SS diverter trim along with a RP6023SS shower arm and RP51034SS flange for the 58470-SS to complete your faucet. You will plumb the diverter rough from the shower port on the R10000 after capping off the tub spout port. You will then cap off the 3 o-clock port on the R11000 diverter rough and plumb the showerheads out of the remaining 9 and 12 o-clock ports. The 3 setting diverter will allow you to operate each showerhead individually or both at the same time.
Thanks,
Dave
Skill Level: Advanced
8 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about DeltaFaucet2 is loaded.
Additional information about DeltaFaucet2 could not be loaded.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
  • 2016-02-06 T03:27:11.377-06:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_R11000, prod, sort_default
2 3 next>>
  • 2016-02-06 T03:27:11.380-06:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_R11000, prod, sort_default
  1. The manufacturer's list price (U.S. dollars) is shown for comparison only. The actual retail price may be different from the price shown.
  2. HGTV and HGTV Dream Home and their associated logos are trademarks of Scripps Networks, LLC. Used with permission; all rights reserved.