Trinsic®

Floor Mount Tub Filler - Rough with Stops

Download Image

R4700-FLWS is rated 5.0 out of 5 by 1.
  • y_2018, m_12, d_9, h_15
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.9
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_en_US, sid_R4700-FLWS, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_deltafaucet
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 27ms
  • REVIEWS, PRODUCT
Finish: Not Applicable
List Price*: $360.55
Base Parts
R4700-FLWS
List Price*: $360.55
Rated 5 out of 5 by from Delta Freestanding Tub Filler Rough-in Valve with Stops. If your interested in local building codes... As far as I know, this delta freestanding rough-in valve is the most cost effective way to meet plumbing codes where I'm from, which require you to have a shut off for all inaccessible valves. I use it in concrete floors and it works like a charm. Just make sure the copper is completely protected from the concrete. Their tub fillers are all thermostatic as well, so you don't have to worry when the inspector comes. As long as its level, and you have adequate setbacks from the wall and tub, installation should be a small feat for any professional. Heavy and beautiful, highly recommend. [This review was collected as part of a promotion.]
Date published: 2018-02-07
  • y_2018, m_12, d_9, h_15
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.9
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_en_US, sid_R4700-FLWS, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_deltafaucet
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 12ms
  • REVIEWS, PRODUCT

What is the difference between this R4700-FLWS and the R4700-FL? The freestanding tub filler needs to be mounted on concrete subfloor. Thank you.

Asked by: Gleneages
Hello Gleneages, Thank you for your question. The R4700-FLWS has supply stops that allow you to shut off the water at the valve during installation. It also will accepts threaded supply connections. The R4700-FL does not have stops and requires soldering. These are the only rough-in valves for our freestanding tub fillers. Please know that all of our products meet or exceed industry standards for performance and safety. Best regards, Tanya
Answered by: Delta Faucet
Date published: 2018-06-12

What size and thread type are the 4 mounting screws

Asked by: Zac
Hi Zac, Thank you for your question. The subfloor mounting screw threads are a #8-15 x 1.25". The trim mounting bolts come in 2 different lengths, 1/4-20 x 2.32" and 3.70". Thanks, Jon
Answered by: DeltaFaucet3
Date published: 2017-03-09

Can I adjust the pressure of the water filling the tub?

Asked by: Neal
Dear Neal, Thank you for your question. The pressure of the Delta Floor mount tub filler rough R4700-FLWS valve, can not be adjust for different pressure or temperature. The cartridge assembly of this faucet can be adjust for hotter or colder water, but not the pressure. Best regards, Tanya
Answered by: Tanya
Date published: 2017-02-18

I see from the instructions that it is mounted with the plasterguard in place. Cut it off when installing filler?

It is attached the the rough so I was wondering if it stays on and I cut it off when installing the filler trim.
Asked by: Archie
Yes, right before you install the trim, cut off the plastic shield even with the floor. I used a utility knife and it cut fairly easy. Hope this helps, Jim
Answered by: Jim62
Date published: 2017-06-10

Hot Water Adjustment

We have the R4700-FLWS with stops and there is not enough hot water. Can the faucet be adjusted to increase the hot water?
Asked by: Greg
Thank you for your question, Greg. Some Tub Filler trims have a Rotational Limit Stop. Please refer to page 7 of the instructions linked below. Please also make sure that the supply stop on the hot side is fully open. https://media.deltafaucet.com/MandI/74820%20Rev%20D.pdf Best regards, Jon
Answered by: DeltaFaucet3
Date published: 2016-11-29

what is the tub filler flow rate

Asked by: Rick
Hi Rick, Thank you for your question! The tub filler should run at least 6 gallons per minute at 60 PSI. However, the exact flow rate will be determined by the trim kit that you use. Please refer to the Technical Specifications under the "Documents and Specs" tab on the product page for the trim kit you will be using. Best regards, Jon
Answered by: DeltaFaucet3
Date published: 2016-11-14

What is the model number for the required trim?

Asked by: nay
Hi Nay, Thank you for your question. The T4752-FL, T4759-FL, and the T4797-FL are the free standing tub filler trims that work with the R4700-FLWS rough. http://www.deltafaucet.com/bath/romantub/filter-results.html?sort=pricehighlow&type=type-roman-tubfiller&function=bath-romantub Thanks, Dave
Answered by: DeltaFaucet2
Date published: 2016-02-23

What is the flow rate on this valve?

I cannot find the flow chart anywhere on the specs or installation documents.
Asked by: JessiL
Hi JessiL, Thank you for your question. The flow rate for the R4700-FLWS is determined by the faucet trim placed on it. The flow rate for the faucet is 6 gpm @ 60 psi. Thanks, Dave
Answered by: DeltaFaucet2
Date published: 2015-01-07
  • y_2018, m_12, d_9, h_15CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.9
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_8
  • loc_en_US, sid_R4700-FLWS, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_deltafaucet
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 29ms
  • QUESTIONS, PRODUCT