Is there a brushed nickel option
I purchased the Porter 142984-BN-A and wanted to add a brushed nickel wand. Is there a brushed nickel available to match? All i see the stainless that “appears” close
Thank you for your question. We do not make a diverter trim in the Brushed Nickel finish. However, Stainless Steel is a brushed finish that is very similar to Brushed Nickel. We recommend comparing them in the store.
Date published: 2017-11-06
Which valve is this"
I have a 3 position diverter that came in a 3/6 box (T11800 versis T11900). The replacement sent is says this on the stem "Fluhs 60567 and 161117". I can't compare with the temp. installed 3, but it looks the same. Delta pic on site for 6 shows (all I can see) https://www.deltafaucet.com/parts-product-detail?modelNumber=RP51919
"uhs __563 and __1109" which leads me to believe it is again the 3/6.
Maybe in the future Delta could show all numbers on parts instead of just partial!!!!
Thank you for your question. The Delta 3-Setting Diverter Trim T11800 comes with the 3-Setting Diverter Cartridge Assembly RP51918. The Delta 6-Setting Diverter Trim T11900 comes with the 6-Setting Diverter Cartridge Assembly RP51919.
Date published: 2017-05-30
Is there trim that can be used when the hole for the diverter is larger than the trim?
I have the t11800 and I made the hole the same size as the valves. the depth is about on the money slight in too far so the plate can push out the diverter trim too much.
Thank you for your question, Steve. The RP42414 will fit behind the plate, and may help cover the hole.
Date published: 2016-12-22
At 60PSI, what is the flow rate (in GPM) from each port when not in the shared position? and from each port when in the shared position?
Hello Steve, Thank you for your question.
The GPM ( gallons per minute) of the positions for the T11800/R11000 diverter valve depends on the components being used and the trim/cartridge of the control valve. Below is a general chart:
Approximate Outlet Flow Rate (gpm)
Pressure (psi) 13 Series 17 Series 17T Series
30 3.7 3.5 4.0
40 4.3 4.1 4.6
50 4.8 4.6 5.1
60 5.3 5.0 5.6
70 5.7 5.4 6.1
80 6.1 5.8 6.5
Date published: 2016-09-19
Can this faucet be configured to have an off position?
I would like to be able to have overhead shower or a wand or the off position not both in one position.
Thank you for your question. This diverter will allow you to run two components, together or individually. The diverter cannot be configured to turn the water off to both units. You must have a separate valve to control the flow and temperature of the water, such as a 14, 17, or 17T series unit. To narrow narrow down your selection, please click the link below.
Date published: 2016-05-05
Depth of installation problem
I have this R11000 diverter with the T11800 trim kit. I had a plumber do all the rough-in, but now that the tile is up and I'm installing the trim, I've found that the plumber put the valve at the wrong depth.
While the shower valve trim (a Symmons) itself was fine, the diverter backplate is actually sitting 3/8" from the wall. Is there an alternate trim or a extension plate available that resolve this? Untiling the wall is not an acceptable solution!
Hi Larry, We are sorry that you are experiencing a problem with your installation. Unfortunately if the valve is plumbed out too far we do not offer any alternative trim rings or extensions to fix the issue. The valve will have to be replumbed. Step 1 of the attached installation manual shows the dimension at which the diverter rough should be installed.
Date published: 2015-05-29
Matching trim for shower valve?
What is the part number for the matching trim for the R10000-UNBXHF Shower valve in Venetian Bronze?
Hi Jerryr, Thank you for your question. Shower trims from our Leland collection models T14278-RBLHP H778, and T17278-RB as well as trims from our Lahara collection T14238-RB and t17238-RB will match the T11800-RB and use the R10000-UNBXHF high flow rough.
Date published: 2015-01-27
Handle for this diverter trim
I have the H212PB handles for my faucets and wonder if there is a matching handle replacement that will fit this diverter... such as H512PB? Or if there is a porcelain insert to replace the small brass lever?
Thank you for your question. Sweet Lou is correct. Thanks for the contribution.
Date published: 2013-10-22