Lakeview

Pull-Down Kitchen Faucet with Soap Dispenser

Download Image

  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 64ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;
  • 2 or 3-hole installation
  • Delta MagnaTite Docking holds spray wand firmly in place
  • Backed by Delta Faucet's Lifetime Limited Warranty
Finish: Venetian Bronze
List Price*: $430.50
Base Parts
59963-RBSD-DST
List Price*: $430.50
The pull-down spray wand comes free with a gentle tug and gives you total flexibility. The hose extends and retracts without friction points, fed by gravity. As you raise the wand to dock it, the magnet embedded in the spout pulls the wand precisely into place. So, unlike other pull-downs that tend to droop over time, MagnaTite® keeps your pull-down faucet looking picture-perfect. Delta's exclusive DIAMOND Seal® Technology uses a valve with a tough diamond coating. InnoFlex® PEX waterways keep water inside the faucet out of contact with potential metal contaminants. This powerful combination brings you a faucet built to last up to five million uses. Only Delta faucets are equipped with Touch-Clean® soft, rubber nubbins that allow you to easily wipe away calcium and lime build-up with the touch of a finger.
  • MagnaTite docking keeps the kitchen pull-down spray wand firmly in place with a powerful integrated magnet, so it stays docked when not in use
  • DIAMOND Seal Technology features a valve embedded with diamonds to ensure like-new operation for the life of the faucet
  • Includes matching finish soap dispenser
  • Meets standards set by Americans with Disabilities Act
  • 2 or 3-hole 4 in. installation
  • The high-arc, gooseneck design swivels 360 degrees with a 20-in. retractable hose for added convenience during everyday kitchen tasks

Technology

Special Features

Installation Information


2 or 3-hole 4" installation


  • Flow Rate: 1.80 gpm @ 60 psi, 6.8 L/min @ 414 kPa
  • Fittings Type: PEX
  • Supply Lines: Included InnoFlex® Pex-C Supply Lines
  • Valve Type: DIAMOND Seal Valve
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 10ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;

need flange for sink drain and garbage disposal & add'l soap dispenser

I am considering purchasing the Lakeview Pull Down Faucet with Soap Dispenser and would like to know the availability of coordinating parts. I am looking to replace the 3 1/2" flange for the sink and the 3 1/2 " flange for the garbage disposal in addition to another soap dispenser all in the coordinating "Venetian Bronze". Can you tell me where to purchase these parts since this is part of the Home Depot only collection along with the item/part numbers. Additionally, is it customary to change the flanges to match a new faucet?
Asked by: pamb
Hello Pamb, Thanks for your question. Unfortunately, the only flange for a kitchen sink and garbage disposal that we make is 4 and 1/2" in diameter. The part number for the soap dispenser is RP50781RB.
Answered by: DeltaFaucet4
Date published: 2015-09-15

My question is as follows:  Why hasn't every company adopted the excellent communication skills that Delta reps exhibit?  We have nothing but positive things to say.  We thank you for your support recently.

Asked by: Mauley
Hi, Mauley! Thank you for your question and your kind words. We're happy to have been able to assist you with your faucet. If you should need any other assistance in the future, please let us know! Thank you for being a loyal Delta customer. Best Regards, Rosanna
Answered by: DeltaFaucet11
Date published: 2018-06-06

Would it be correct to convert the Pex C faucet lines to 3/8X1/2 male thread.  The current supply lines are 30" flexible with 1/2" fittings on both sides.  That is the main reason for the question.  

Asked by: Mauley
Thanks for the reply, however, I would like to use shark bite type fittings.  I think there is a 3/8" X 1/2" male thread shark bite.  If this is OK, then I should be able to push the 3/8 side into PEX and have the 1/2" male ready for the female connection. thanks again John
Answered by: Mauley
Date published: 2018-05-21

Can it switch to a left hand 

Asked by: Rangerman
Thank you for your question, Rangerman! The handle can be installed on the right or left of the spout. Best regards, Jon
Answered by: Delta Faucet
Date published: 2018-11-27

can the Lakeview be installed with spacing other than 4 inch centers?

I have had in past one center hole for main faucet w integrated control lever --- second hole is 7.5 inches on center to the right of the main faucet hole and was for a hand held spray , soap dispenser is way to the left 18 inches from center faucet hole so I need 3 "components" for the 3 holes but was not sure if the main faucet and control lever for the Lakeview have to be 4 inches on centr apart or can they be spaced further apart?? - assume soap dispenser is separate and not critical on spacing?
Asked by: Lee
Hi Lee, Thank you for your question. The spout and valve on the model 59963-SSSD-DST can be placed further apart. However the wider the spread the shorter the length of the pull down sprayer. Thanks, Dave
Answered by: DeltaFaucet2
Date published: 2016-09-24

What is the absolute minimum clearance between the back-splash and the base of the faucet?

I see the spec sheet says 2.5" clearance to the back-splash but I don't see why so much space is required. Our current faucet sits almost against the back-splash as we have a narrow space behind our sink, and the current faucet is 2.25" diameter. If this faucet will not work in this configuration can you recommend another Delta product that will? Thank you.
Asked by: Julie
Hi Julie, Thank you for your question! The minimum back splash clearance for all of our kitchen faucets is 2 1/2. This is to allow clearance for the operation of the handle ( most handles go back to turn on) and also for the clearance of the spout ( spouts either swivel 360 degrees or 180). Best regards, Brandis
Answered by: DeltaFaucet7
Date published: 2016-03-28

Can the water supply lines be cut to fit?

Asked by: John
Thank you for your question, John. We recommend looping the supply lines as long as the loop is 8" or more in diameter. However, you may cut the supply lines by following the instructions under the section titled "Custom Fit Connections". Please see page 5 and 6 of the Installation Instructions linked below. Note that Delta is not responsible for tubing that is cut too short or cut in a way that will not allow for a leak-free joint. https://media.deltafaucet.com/MandI/73046%20Rev%20C.pdf Best regards, Jon
Answered by: DeltaFaucet3
Date published: 2017-09-25

Can you please tell me what the height of this faucet is, at the highest point of the arc?

I'm trying to determine if I have room under an above-sink shelf.
Asked by: CeCe
14.5 inches total to top of spout arc
Answered by: MacGyver
Date published: 2017-01-14
  • y_2019, m_9, d_20, h_15CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_19
  • loc_en_US, sid_59963-RBSD-DST, prod, sort_[SortEntry(order=HAS_STAFF_ANSWERS, direction=DESCENDING)]
  • clientName_deltafaucet
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 42ms
  • QUESTIONS, PRODUCT