Single Handle Bathroom Faucet in Polished Nickel

Hi, Nancy. Thank you for your question. We do not manufacture plugs for sink application. The escutcheon plate for the Delta 597LF-MPU faucet is a 4" center installation and will not cover 6" installation. Best Regards, Rosanna

Hello, Thank you for your question! This model uses a push pop-up drain which you press with your hand to pop up and again to engage. Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Dear Cm811, Thank you for your question! The Delta Cassidy Lavatory 597LF-MPU faucet is only designed with the handle on the right side of the faucet. https://media.deltafaucet.com/PartsDiagram/DPD-L-597LF-MPU.pdf Best regards, Tanya

Hi, JStar! Thank you for your question. There is a small pivot seal and gasket that would need to be unscrewed to remove the stopper from the horizontal rod underneath the sink. Once this is unscrewed off, you can remove the stopper from above the sink. Here is a link to the parts diagram for the pop up drain assembly to show these parts to you: https://media.deltafaucet.com/PartsDiagram/RP26533_Pop_Up_Drain.pdf Best Regards, Rosanna

Thank you for your question, Buster! Model 597LF-SSMPU does not swivel however the 1997LF Bar Prep does swivel 360 degrees and could be installed as a lavatory faucet if needed. https://www.deltafaucet.com/product-comparison?modelNumber=1997LF&modelNumber=597LF-MPU Best regards, Edward

Hi, Ksanders78! Thank you for your question, and I am sorry to hear that you are experiencing low flow from your Delta faucet. You may need to flush out the valve body. To flush out the valve body, first turn off the water supply to the faucet.           1. Remove the handle. On the lever handle, you should find a small hex screw that can be loosened with a 3/32" Allen wrench. The handle will lift off when this screw is loose enough.           2. Once the handle has been removed, unscrew the dome-shaped cap. The domed shaped cap will unscrew counter-clockwise.            3. Unscrew the bonnet nut under the cap.          4. After these parts have been removed, you can then pull the valve cartridge assembly straight out.           5. Now, with the valve completely disassembled, place a bucket upside down over the top of the empty brass valve body. Turn the hot and cold water supplies back on and let the water run for about 10 to 15 seconds. The water will come directly up out of the valve and should mostly be deflected back into the sink by the bucket. You might have a little bit of water to clean up, though!           6. Shut off the water supplies. Make sure that the valve cartridge assembly does not have any debris stuck to them and reinstall them. Reinstall the valve cartridge assembly. Reinstall all parts. At this point, you can test the faucet again. If this does not fix the issue, please contact our Delta Customer Service line at (800)345-3358. We are available Monday-Friday, 7am-7pm, CST and Saturday, 8am-5pm, CST. You may also email at customerservice@deltafaucet.com. Best Regards, Rosanna

Hi SJHomeowner, Thank you for your question. The spout from the model 597LF-RBMPU measures 5-13/32" from the faucet center to the center of the water stream. The faucet should fit a sink bowl with your dimensions. Here is a link to the spec sheet for the model 597LF that shows this and other faucet dimensions. http://www.deltafaucet.com/customersupport/documentation/597lf-rbmpu.html?document=ts&fromDetailArea=bath&documentIndex=0#flashWrapper Thanks, Dave

Hi, Ernie! Thank you for your question. The Delta 597LF-RBMPU faucet does not have an 8" escutcheon option. The escutcheon plate for the faucet is part number RP72711RB. This will fit a 4" center installation. Best Regards, Rosanna

Hi JW, Thank you for your question. The overall height of the model 597LF is 6-13/16". Here is a link to the spec sheet for the faucet. http://www.deltafaucet.com/customersupport/documentation/597lf-ssmpu.html?document=ts&fromDetailArea=bath&documentIndex=0#flashWrapper Thanks, Dave

Dear Need2no, Thank you for your question. The Delta Cassidy Lavatory 597LF-MPU has a recommended distance minimum 2 1/2" (64 mm) clearance to the back splash, to ensure room for the lift rod of the faucet. This is the say recommended clearance for all of the standard lavatory Delta faucets. We would advised possible vessel sink style faucets for your install. Best regards, Tanya

Hi, Leslie! Thank you for your question. The Delta 597LF-MPU faucet handle pulls out for cold and pulls toward you for hot. Best Regards, Rosanna

Hello, cooper5ab! Thank you for your question. Unfortunately, we do not have a part to convert the existing pop-up assembly to a push-pop up. However, you can purchase a complete drain assembly such as the 72173 Push Pop-Up with Overflow for use with this faucet. https://www.deltafaucet.com/parts-product-detail?modelNumber=72173 Best regards, Jon

Hello! This model uses the RP73000 valve cartridge. https://www.deltafaucet.com/parts/product/RP73000.html Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Dear MM, Thank you for your inquiry! Yes, the exterior of the Delta Cassidy Lavatory 597LF-MPU faucet is made of metal. Best regards, Tanya

Hello Jani, Thank you for your question. Delta faucet 597LF-RBMPU is ADA compliant. Best Regards, Courtney

hi mtnbykmyk, Thank you for your question. Unfortunately, we do not have a higher flow or laminar flow aerator for this faucet. Best regards, Jon

Hi KeithA, Thank you for your question. The model 597LF-MPU faucet can be installed on 4" centers. The faucet comes with an optional escutcheon that will cover the unused holes. Thanks, Dave

Hello Valpar3, Thank you for your question. The handle of the Delta Cassidy Lavatory 597LF-MPU faucet is designed for this specific model style. We can not guarantee the parts of our faucet will work/fit with other company faucets or parts. Best regards, Tanya

Hi KikiB, Thank you for your question! The handle will only rotate forward from the upright position. However, we do recommend to have 2 1/2" clearance from the center of the faucet to the back splash. Best regards, Jon

Hello Kim S, Thank you for your question. The handle temperature rotation of the Delta Cassidy Kitchen 9197-AR-DST and Lavatory 597LF-MPU faucets are just differently designed. However switching the supply lines connections to the valves, below he sink on one of the units would be a suggestion we would have. Best regards, Tanya

Hello Jet333, Thank you for your question! The Delta Cassidy Lavatory 597LF-MPU faucet is only designed with the handle on the right side of the faucet. Best regards, Tanya

Hi Cavs, Thank you for your question about the Delta Faucet model 597LF-PNMPU. We recommend a minimum of 2.5" clearance to the backsplash from the hole center. Unfortunately, we are not able to recommend installing our faucets with less clearance as it can be difficult to use or clean the faucet. Please reach out with any additional questions! Best Regards, Bryan Digital Communications Specialist

Good morning Pat831, Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available, and I am happy to help you! Our Delta CASSIDY™ Single Handle Bathroom Faucet MODEL#: 597LF-MPU tailpiece for the drain is not manufactured in oil rub bronze. The tailpiece is only manufactured in chrome finish. Thank you for being a loyal Delta customer. Please contact us back with any further questions. Best Regards, Themar

Hello Valued Customer, Thanks so much for contacting Delta Faucet Company about 597LF-SSMPU! Leaking under the handle can be caused by the bonnet nut being loose, we would recommend removing the handles and tightening the bonnet nuts. Start by shutting off the water to prevent a possible issues when troubleshooting. Please contact us directly if you have any questions or need additional assistance. Best Regards, Nicole Digital Communications Specialist

Hello Frank, Thank you for contacting us, I would be happy to help you. I have attached the installation sheet below, please see page 3 box H. https://media.deltafaucet.com/MandI/86520%20Rev%20F.pdf Please contact us back if you have any questions or need further assistance.  Best Regards,  Nicole

Hello! Thank you for contacting Delta Faucet Company! Please verify the production date on the sticker that is located on the hot water line of the faucet. For 597LF-MPU models produced after 4/28/2024, the aerator is RP101953-1.2. For 597LF-MPU models produced prior 4/28/2024, the aerator is RP52657-1.2 with aerator wrench RP46858. https://www.deltafaucet.com/bathroom/product/597LF-MPU.html# We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Communications Specialist

Hi Turbo, Thank you for your question! We apologize that the information you are searching for was not readily available. We realize that can be very frustrating and I am happy to assist you! We thank you for being a loyal Delta Faucet customer. The Delta Faucet part RP52657-1.2 Dryden™ Aerator - Water-Efficient - 1.2 GPM is the recommended replacement for the Delta Faucet model 597LF-RBMPU Cassidy™ Single Handle Bathroom Faucet In Venetian Bronze. It can be ordered locally or online. Please see our Where to Buy page for help finding dealers in your area or online. https://www.deltafaucet.com/where-to-buy Please contact us back directly via email with any further questions. Best Regards, Skyler

Hello TonyC, Thank you for contacting us, I would be happy to help you. This assembly should work with a 1 1/2" diameter drain. However, the depth of the hole must be 1 5/8" to 2 3/8". Please contact us back if you have any questions or need further assistance.  Best Regards,  Nicole

Hello Andrew Somple, Thank you for your question! We apologize for the flow issue you are experiencing and will be happy to help you. Reduced flow is typically caused by the debris. We recommend flushing the unit. To flush the unit: Remove aerator using supplied wrench and turn faucet handle to the full on mixed position. Turn on hot and cold water supplies and flush water lines for one minute. This flushes away any debris that could cause damage to internal parts. Reinstall aerator with wrench. Check all connections at arrows for leaks. Retighten if necessary, but do not overtighten. Please refer to page 4 section 5 of the maintenance and installation guide for more details. I have attached the link below. https://media.deltafaucet.com/MandI/86520%20Rev%20F.pdf Thank you for being a loyal Delta Faucet customer. We look forward to continuing to serve you. Please feel free to contact us back for further assistance. Best Regards, Kelley