Single Handle Tub and Shower in Chrome

Hello, Thank you for your question! Unfortunately this model is not available in that finish. However, please see the following link for our tub and shower trim kits that are available in the matte black finish. https://www.deltafaucet.com/bathroom/showering/tub-and-shower-faucets?cgid2=Delta_Bathroom_Showering_Tub-and-Shower-Faucets&prefn1=clearance&prefv1=false&prefn2=finish&prefv2=Matte_Black&prefn3=narrowResults&prefv3=hideDiscontinued&prefn4=recertified&prefv4=false&srule=price-low-to-high Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Hello, Please accept our sincere apology for the inconvenience you are experiencing. We have reached out to you via email to further assist at this time. Best Regards, Tim Digital Communications Specialist

Hi, Chris. Thank you for your question. We do not recommend welding the copper pipe inside the manifold for the Delta B114915C Tub and Shower Unit. We recommend reading the instructions before installing. Here is a link to the Maintenance & Installation Sheet for the faucet: https://media.deltafaucet.com/MandI/101650%20Rev%20B.pdf Best Regards, Rosanna

Hi, Phyllis! Thank you for your question. The Delta B114915C does include the RP70538 Valve Cartridge Assembly. Best Regards, Rosanna

Hello Jimmy Patel, Thank you for your question. Unfortunately, we do not have a video for adjusting the limit stop on the Delta Foundations Shower B114915C faucet model. However, to adjust the limit stop: First, remove the handle and adapter nut on the faucet and set them aside. You will now see a small black o-ring on the end of the brass stem. Remove this o-ring and again set aside. The next piece is the limit stop, you may see the words hot/cold. Rotate this part clockwise for hotter water. Each notch you move the piece, it will increase the maximum hot water by approximately 2-3 degrees. Reinstall the o-ring, adapter and handle. Please see page 7 of the instructions linked below. https://media.deltafaucet.com/MandI/88723%20Rev%20A.pdf Best regards, Tanya

Hello Brian White, Thank you for your question. Based on your description of the flow from the tub/shower, you are experiencing an issue known as shower rise. This is an installation issue, which has several possible causes: The valve could be upside down. The length from the valve to the tub spout is outside of the 8" to 18" rule. There is more than one 90-degree angle elbow. Something other than ½" smooth copper or galvanized pipe was used going to the spout. No push fittings. No "shark-bite" fittings. No cast or drop ear elbows. Something restricting the water flow to the spout, e.g. solder or something lodged in the pipe. If this is the cause of shower-rise it is possible to remove the blockage by removing the tub spout; then, feeding a plumber’s snake or a speedometer cable up through the tub drop. The act of feeding it causes it to twirl and loosen the blockage. Be sure to flush the valve before reinstalling the tub spout. Be sure to check the tub spout itself for blockage. Please feel free to call, email, or message us on social if there is anything else you need. Best regards, Tanya Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

Hi, Glenn! Thank you for your question. The Delta B114915C Tub and Shower Unit does not have an adjustment for water flow. The volume for the unit only comes on at full volume. Best Regards, Rosanna

Hi, Will! Thank you for your question. Here is a link to the Maintenance and Instruction Guide for the Delta B114915C Faucet to show how to adjust the rotational limit stop on page 7: https://media.deltafaucet.com/MandI/101650%20Rev%20B.pdf Best Regards, Rosanna