MultiChoice® Universal Integrated Shower Diverter Rough Universal Inlets / Outlets

Hello Khan, Thank you for your inquiry! A shower head and hand shower can be installed/used with the Delta Integrated Rough-In Valve R22000 and trim of your choice. You would need to purchase the non-shared 3-Function Diverter Cartridge RP71717 for type of installation. https://www.deltafaucet.com/parts-product-detail?modelNumber=RP71717 Best regards, Tanya

Hello Tbest4475, Thank you for your inquiry! When installing the Delta Integrated Rough-In Valve R22000 with a 3-setting diverter trim, only the top and left ports will be in use. If you are only using two ports, one for your shower head and one for your hand shower, you must plug the right port. If the left port was capped off instead, you can purchase just the 6 setting diverter cartridge, RP51919, so that all of your setting will work with your existing trim. https://www.deltafaucet.com/parts-product-detail?modelNumber=RP51919 Best regards, Tanya

Thank you for your question, Jeff! The R22000 will use a cartridge that has a rational limit stop which limits how hot the water will get. This should be adjusted at the time of installation however the information on making this adjustment can be found in the Maintenance and Installation manual for the trim kit you choose. https://media.deltafaucet.com/MandI/104437%20Rev%20A.pdf Best regards, Edward

Hi, Jason. Thank you for your question. We recommend to either replumb the lines from the right port to the left port, or you can purchase a 6-setting diverter cartridge. The part number is RP51919. You will have some blank settings but the three settings needed, will work properly. Here is a link to the cartridge: https://www.deltafaucet.com/parts-product-detail?modelNumber=RP51919 Best Regards, Rosanna

Thank you for your inquiry, Jeff! The cap can be soldered into the port, or you can purchase a threaded cap separately. Best regards, Tanya

Hello NH_Al, Thank you for your question. The Delta MultiChoice Universal Integrated Shower and Diverter Rough-In R22000 valve is not designed to be used with a tub spout. However, you may connect a non-diverter tub spout to one of the diverter ports as a temperature tester. Since the flow rate from the spout would be lower than a standard installation, we do not recommended to use it as a tub filler. Alternatively, you can install an R10000 and R11000 valve with corresponding trim kits. The tub spout should be connected to the bottom port of an R10000 valve to provide sufficient flow to fill a tub. https://www.deltafaucet.com/bathroom/product/R10000-UNBX https://www.deltafaucet.com/bathroom/product/R11000 Best regards, Tanya

Hi Rosanna, Delta team, can u pls elaborate li'l more on why it can't be used with tub spout. And, do you have any other similar model with 3 outlets one of which can be used with tub-spout? thanks.

Hi, Jim Fel. Thank you for your question. With a 3-setting diverter trim, only the top and left ports will be in use. We recommend a 6 setting diverter trim. We recommend the T27967 6-setting trim kit. Or, you can purchase just the 6 setting diverter cartridge, RP51919, so that all of your setting will work with your existing trim. If you just want 3 individual settings and no shared settings, we recommend to purchase the RP71718. Best Regards, Rosanna

kerk1950, Thank you for your question. The valve has a 1/2" connection, so larger diameter supplies will need to be adapted to fit, reducing any gains in flow rate. The maximum flow rate will depend mostly on the trim kit that you use, as the cartridge is where the water will be restricted the most. Here are the approximate maximum flow rates at 60 PSI per series: T248/T249 series - 5.0 GPM T278/T279 series - 5.8 GPM T27T8/T27T9 series - 7.2 GPM Best regards, Jon

Hi, Chris! Thank you for your question. The Delta R22000 will work with 3 shower components. The cartridges will be included with the trim kit that you select. We recommend selecting a trim kit with 6 settings. Here is a link to our Integrated shower trim kits: https://www.deltafaucet.com/bathroom/showering/tub-and-shower-faucets?facetFeature=FltIntegratedDiverter Best Regards, Rosanna

Thank you for your question, Lars! You can find our selection of trim kits with an integrated diverter in the Matte Black finish at the link below. https://www.deltafaucet.com/bathroom/showering/shower-components?facetFinish=matteblack Please note that with integrated models, the showering components are sold separately. You can find our shower heads and hand showers here: https://www.deltafaucet.com/bathroom/showering/showerheads--handshowers?facetFinish=matteblack Best regards, Jon

Hello Tom D, Thank you for your question. The Delta MultiChoice Integrated Diverter R22000 will work with any of the Delta Trim kits starting with the T27 models. https://www.deltafaucet.com/search-results?searchTerm=Integrated+trim Best regards, Tanya

Hi, Sully! Thank you for your question. The Delta R22000 Integrated rough valve body can sweat onto 1/2" C.W.T. or accepts 1/2" iron pipe, PEX or CPVC adapter. Best Regards, Rosanna

Hi Aaron, Thank you for your question! The plug should be soldered to the right outlet port for a 3-setting diverter. Best regards, Jon

Thank you for your question, Paul! We recommend to either replumb the lines from the right port to the left port, or you can purchase a 6-setting diverter cartridge, part number RP51919. There will be some blank settings but the three intended settings, will work properly. Below is a link to the cartridge: https://www.deltafaucet.com/parts-product-detail?modelNumber=RP51919 Best regards, Edward

Hello! No, the top port must be open and ran to the showerhead or hand shower. The right port of the diverter valve section must be capped off. Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Hi, Joel! Thank you for your question. The Delta R22000 Integrated rough valve does work with Delta Monitor® 14 Series Valve Trim with 3-Setting Integrated diverter kits. Here is a link to these options: https://www.deltafaucet.com/search-results?searchTerm=Monitor%C2%AE+14+Series+Valve+Trim+with+3-Setting+Integrated+Diverter#resultPage=0&offset=1100 Best Regards, Rosanna

Hello Nate367, Thank you for your question. This valve is not designed to be used with a tub spout. However, you may connect a non-diverter tub spout to one of the diverter ports as a temperature tester. Since the flow rate from the spout would be lower than a standard installation, we do not recommended to use it as a tub filler. Alternatively, you can install an R10000 and R11000 valve with corresponding trim kits. The tub spout should be connected to the bottom port of an R10000 valve to provide sufficient flow to fill a tub. Best regards, Tanya

Dear Dennis, Thank you for your inquiry! Yes, the Delta MultiChoice R22000 will work with any of the Delta Trim kits starting with the T27. https://www.deltafaucet.com/search-results?searchTerm=t27 Best regards, Tanya

No and it wouldn't help your flow rate anyways since the restrictions will be the orifices in the valve body itself.

Dear Toby, Thank you for your question. This valve is not designed to be used with a tub spout. However, you may connect a non-diverter tub spout to one of the diverter ports as a temperature tester. Since the flow rate from the spout would be lower than a standard installation, we do not recommended to use it as a tub filler. Alternatively, you can install an R10000 and R11000 valve with corresponding trim kits. The tub spout should be connected to the bottom port of an R10000 valve to provide sufficient flow to fill a tub. https://www.deltafaucet.com/search-... Best regards, Tanya

Dear Lucien, Thank you for your question. If you are plumbing the Delta MultiChoice Universal with Integrated Diverter Rough R22000, to be used with 2 showering devices and using a 3 setting diverter trim kit, you will have to cap the right side port. The unit will not function properly if you cap off the left port, you will not get all three diverter setting. Below, please review page 6 section labeled "Water Flow For 3 Function Diverter" for a better function understanding. https://media.deltafaucet.com/MandI/91557%20Rev%20A.pdf Best regards, Tanya

H, Teresa! Thank you for your question. Here is a link to our Delta Integrated Valve and Diverter Trim Kits to work with the Delta R22000 Rough: https://www.deltafaucet.com/bathroom/showering/tub-and-shower-faucets?facetFeature=FltIntegratedDiverter Best Regards, Rosanna

Hi John, Thank you for your question! This valve will work with 14, 17, or 17T series trims with an integrated diverter. The T27867 trim does have separate volume and temperature control as you have described. However, it use a Monitor pressure-balance cartridge to prevent scalding. Thermostatic valves instead balance the temperature of the water (for less variation in temperature). The T27T867 operates the same way as the T27867 but has a thermostatic TempAssure cartridge. Best regards, Jon

Dear Japlaza, Thank you for your question. The Delta MultiChoice Rough-In valve R22000 comes with test caps. The cartridge assemblies for the valves come in the box with the Delta Trim kits with Integrated 3/6 diverter. https://www.deltafaucet.com/search-results?searchTerm=Integrated+diverter Best regards, Tanya

Either is fine. Joint compound is what is used for most commercial pipe thread connections.

Thank you for your question, Rbnh! There are no specific limitations on the distance you can install the shower head from the R22000WS valve, however the extra elbow could possibly create a very slight decrease in pressure depending on the PSI of the home. Best regards, Edward

Hi, Leland! Thank you for your question. We do not have a recommendation for thickness of your finished wall. Once the finished wall thickness is measured, this will determine how far back the Delta R22000 MultiChoice® Universal Integrated Shower Diverter Rough should be installed. Here is a link to the Maintenance & Installation Sheet for instructions on measurements for this install: https://media.deltafaucet.com/MandI/91557%20Rev%20C.pdf Best Regards, Rosanna

"WS" means "With Stops" and it allows the water be turned off (stopped) at the device so you can make repairs without turning off the water to the entire house/building.

Thank you for your question, Kevin. This valve will operate two shower heads and one set of body sprays with a 6-Setting Diverter Trim. Best regards, Jon