Traditional Wall Mount Pot Filler in Venetian Bronze

Hi, Sunshine! Thank you for your question. The longest fold for left and right of the Delta 1177LF-RB Pot Filler measures 11 3/8" (289 mm). We recommend measuring the center on your wall for the best reach and fold application. Best Regards, Rosanna

Thank you for your question. Included here is the spec sheet for Delta Faucet model # 1177LF-RB. http://www.deltafaucet.com/customersupport/documentation/1177lf-rb.html?document=ts&documentIndex=0#flashWrapper

Hi Chris, Thank you for your question. The faucet body is 14" wide when parallel with the wall. When the handle is turned outward, the total width is 16". Technical Specifications: http://www.deltafaucet.com/customersupport/documentation/1177lf-rb.html?document=ts&fromDetailArea=kitchen&documentIndex=0#flashWrapper Best regards, Jon

Hi, Tracey! Thank you for your question. At this time, our Delta Pot Fillers are not compatible with our VoiceIQ Technology. Best Regards, Rosanna

Since Delta is not offering replacement o-rings I disassembled my leaky pot filler and measured the o-rings in the arm joints where it was leaking with a micrometer. There are three o-rings per swivel joint. Based on my measurements I ordered Nitrile Rubber O-Rings size 20mm OD - 14mm ID and 3mm Width from AMZ. You need six but order extra if you damage one during install. The replacement was easy. Turn off the water at the valve closest to the wall. Open the valve at the end to drain any water. Pop off the decretive caps and using a proper size allen (hex) wrench unscrew the connection at the wall valve first. Remove the pot filler. Unscrew the second joint. Remove the old o-ring that is closest to the threads on the brass insert first. Then remove / unscrew the insert completely. You may need to gently push it out with a wooden dowel and rubber mallet. Remove the last two o-rings from each insert. Clean any mineral buildup from ALL parts. I used white vinegar. Dry then lube ALL parts with a small amount food grade silicone grease before and after installing the o-rings to assist with assembly and o-ring wear. Replace just the first two o-rings farthest away from the threads first. Install the inserts back into the pot filler arms. It will be a tight fit. This is where the silicone lube and rubber mallet id needed come in handy. Use a wooden block or socket so you do not damage the brass threads when pushing the inserts through and out the other side. I also slowly twisted the insert with the hex wrench while pushing back in to prevent o-ring damage. Once they are all the way through add the last o-ring. If you try to put all three o-rings on first you will damage the o-ring closest to the threads while pushing the insert back in. Re attach the filler swivel arms pieces first and then the filler back to the wall valve. Tighten securely but do not over tighten. Check for leaks by shutting off the outer valve and turning on the wall valve. Retighten with hex wrench as needed. No leaks? Replace the beauty caps and run the water in a large pot to flush out any excess grease. After replacing the o-rings my pot filler was a bit stiff to move but no longer leaks! :)

Hi, Cj123! Thank you for your question. We do not recommend using our Pot Fillers with reverse osmosis systems. At this time, only our Beverage Faucets can be used with reverse osmosis. https://www.deltafaucet.com/kitchen/specialty-faucets/beverage Best Regards, Rosanna

Hi, Dotha! Thank you for your question. The Delta RP64634 wall mounting kit is included with the Delta 1177LF-RB faucet. Best Regards, Rosanna

Thank you for your question. Delta Faucet model # 1177LF-RB does not have a recommended height for installation. It is customer preference to the size of the pots they will be filling.