Single Handle Kitchen Faucet with Spray in Chrome

Thank you for your question, Jeff! The sprayer found on model B4410LF can be connected using either a threaded connection for some models or the block and o ring connector. First align the tabs with the tabs on the quick connects. Push the quick connects firmly upward and then snap them onto the receiving tube tabs. Pull down moderately to ensure each connection has been made. https://media.deltafaucet.com/MandI/86603%20Rev%20B.pdf https://media.deltafaucet.com/PartsDiagram/DPD-K-B1310LF%20Rev%20B.pdf Best regards, Edward

Thank you for your question, James! Currently we do not offer this or another similar model with a 12 inch spout and we apologize for any inconvenience this may cause. Best regards, Edward

Hi, AmyLynn! Thank you for your question. The Delta B4410LF can be used with a water filter. The aerator has a 15/16"-27 thread size. If your water filter is not fitting, we recommend to check with the manufacturer of the water filter to see if there is an adapter that will work with the faucet. Best Regards, Rosanna

Hi, Mela! Thank you for your question. The Delta B4410LF Faucet does include a removable aerator that can be unscrewed counterclockwise from the spout end. Best Regards, Rosanna

Hello, Please accept our sincere apology for the inconvenience you are experiencing. We have reached out to you via email to further assist at this time. Best Regards, Tim Digital Communications Specialist

Thank you for your question, charlie! The bonnet nut may be too tight which is causing the spout to turn. This nut should be finger tight, then 1/4 to a full turn past that. If that does not help or if you need further assistance with this model, please contact our customer service team directly at 1-800-345-3358 Monday-Friday: 8a.m.-8p.m. EST and Saturday: 9a.m.-6p.m. EST or via email at customerservice@deltafaucet.com. Best regards, Edward

Hi Lance, Thank you for your question. Depending on the supplier code some of the model B4410LF faucets will have supply lines that spin. The connection is made with o-rings and a clip system. The spinning lines will not unthread. The models with this design are the B1310LF-30, B3310LF-30, B4410LF-30 Series faucets. Thanks, Dave

I measured my faucet just now. From the sink to the tip of the sprayer is 40 inches.

Hi PaulaG, Thank you for your question! The RP44476 handle is no longer available to order in the Stainless Steel finish. However, RP28898SS is a very similar handle that will work with your faucet. http://www.deltafaucet.com/repairparts/details/rp28898ss.html Best regards, Jon

A picture would be helpful, but I will try to answer your question based on what I think you are trying to do. Twisting/spinning the copper supply lines is going to result in damage to your pipes and a leak. You need two crescent, or two open end wrenches, one to hold the copper pipe from twisting, and a second to tighten the supply line hose. Don't make it too tight or too loose. I would guess about 10 foot lbs. I would use some teflon tape or Rectorseal Tplus2 on the threaded connections to ensure a watertight fit, which you can get at your local hardware store.

Dear Russell, Thank you for your question. I am sorry to hear that you are having a problem attaching your portable dishwasher to your Delta faucet. Unfortunately, we do not manufacture an adapter that would assist you in attaching your portable dishwasher to your Delta faucet. I am also unable to tell you who may manufacture the adapters. Best Regards, Tanya

If you check Delta's web site, you can ONLY buy the entire spray hose set.

Hi Alan, Thank you for your question! Unfortunately, this model is only designed to fit 4 hole installations. The escutcheon plate cannot be removed. Thanks, Jon

Thank you for your question, JJ1234! The Delta B4410LF can be used with a water filter. The aerator has a 15/16"-27 thread size. We recommend checking with the manufacturer of the water filter to see if this will fit or if there is an adapter that will work with the faucet. Best regards, Edward

Hi, Annie! Thank you for your question. The Delta B4410LF-SS Faucet does not use a valve cartridge assembly. This faucet uses the RP77763 Repair Kit. Here is a link to the kit: https://www.deltafaucet.com/parts-product-detail?modelNumber=RP77763 Best Regards, Rosanna

Hi Anne, Thank you for your question. To remove the spray hose from your model B4410LF-SS faucet you will need to press in on the textured portion on the tabs on 2 sides of the white block connector. Once you have applied pressure, push up slightly and then pull the hose down off the fittting. Thanks, Dave

Thank you for your question, Larry. I am sorry to hear you are experiencing a problem with your faucet. It sounds like the water pressure drop could be caused by a debris in the supply lines or faucet. During installation it is always key to flush the faucet and supply lines to prevent debris from becoming lodged in the faucet. On this post I have attached a link of a how-to-video that will explain how to flush the lines. Learn how to flush the lines of your kitchen faucet. This video is generalized for faucets and showers. Your specific faucet may not be covered or featured and could be different. If you have any questions please call 1.800.345.DELTA our team will be happy to walk you through this process and provide any assistance you may need to resolve the issue.

Hello BostonDean, Thank you for your question. The Delta Foundations Kitchen B4410LF-SS faucet can be used without the sprayer, if you get a plug for the spray connection nipple. We recommend part number RP60295. Best regards, Tanya

Hi, Megan! Thank you for your question. Unfortunately, there is not a way to convert the Delta B4410LF-SS Faucet to the Delta B3310LF-SS as the escutcheon plates are non-removable for both faucets. Best Regards, Rosanna

Hello Jack, Thank you for your question! We will be happy to help you. To remove debris from your faucet, you will need to flush. Below you will find the instructions for flushing your faucet. Please gather 1/8” allen wrench, strap wrench, bucket and a towel. ** Please shut off water supplies before starting this process. ** 1. Please remove the handle with your 1/8” allen wrench and pull off the handle. 2. Once the handle has been removed, please remove the dome shape cap with your strap wrench. 3. Once this has been removed, please remove the inside parts. 4. Once you removed these parts, place the towel around the back of the entire faucet and place the bucket on top of the towel leaving some in the sink. 5. While someone else holds the bucket, please turn the hot and cold water supplies on and allow the water to flow for about a minute or so. Feel free to contact us directly, if you have further questions. Best Regards, Renna

Hi Daisy, Thank you for your question about the Delta Faucet model B4410LF. To install the side sprayer, push the quick connect firmly upward and snap it onto the receiving tube tab. Pull down moderately to ensure the connection has been made. See the installation manual here: https://media.deltafaucet.com/MandI/86603%20Rev%20D.pdf Please contact us directly if you have any additional questions! Best Regards, Bryan Digital Communications Specialist

Hello None, Thank you for contacting us, I would be happy to help you. Unfortunately the single handle waterfall is discontinued, but if your looking for a similar model we have two. I have added the links below: https://www.deltafaucet.com/kitchen/product/4380-DST https://www.deltafaucet.com/kitchen/product/11946-SSSD-DST Please contact us back if you have any questions or need further assistance.  Best Regards,  Nicole

Hello Mlposey, Thank you for your question regarding the Delta Faucet Single Handle Kitchen Faucet With Spray, model B4410LF! Please accept our sincere apology for the inconvenience you are experiencing. Here is what we can do to resolve your issue for you. This model does require the escutcheon base. Please feel free to contact us with any questions or for further assistance. Thank you for being a loyal Delta Faucet customer! Best Regards, Emma Digital Communications Specialist

Hi Saxman18, Thanks so much for contacting Delta Faucet Company! To resolve the noise coming from the FOUNDATIONS® Kitchen Faucet MODEL#: B4410LF remove and clean Diverter Assembly. Please refer to page 4 of the maintenance and installation guide. I have attached the link below. https://media.deltafaucet.com/MandI/86603%20Rev%20E.pdf If this does not resolve the issue please call us for a replacement Diverter Repair Kit MODEL#: RP44124. Please reach out with further questions! Best Regards, Kelley Digital Communications Specialist

Hi Mias, Thanks so much for contacting Delta Faucet Company! The FOUNDATIONS® Kitchen Faucet With Spray MODEL#: B4410LF handle can be tightened by using the enclosed wrench. Please reach out with further questions! Best Regards, Kelley Digital Communications Specialist

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Please feel free to contact us directly for warranty information at 800-345-3358. We are available Monday through Friday from 8 a.m. to 8 p.m. and Saturdays from 9 a.m. to 6 p.m. Eastern Standard Time. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist

Hi B4410lf, Thank you for your question about the Delta Faucet model B4410LF Foundations® Single Handle Kitchen Faucet With Spray In Chrome. We will be happy to assist you as quickly as possible. When making the water supply connection be sure to use two wrenches and do not overtighten. Then remove the faucet aerator and check for leaks while flushing the faucet. See the installation manual for more information: https://media.deltafaucet.com/MandI/86603%20Rev%20D.pdf Please contact us directly if you have any questions or need additional assistance. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you! Best Regards, Bryan Digital Communications Specialist

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Please feel free to contact us directly for technical or warranty information at 800-345-3358. We are available Monday through Friday from 8 a.m. to 8 p.m. and Saturdays from 9 a.m. to 6 p.m. Eastern Standard Time. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist

Hi KB0K, thank you for your interest in the B4410LF! To remove the quick connect you will need to press in on the textured portion on the tabs on both sides of the white block connector. Once you have applied pressure, push up slightly and then pull the hose straight down off the fitting. Please contact us directly if you have any questions or need additional assistance. Best Regards, Themar Digital Communications Specialist