Drain - Tub in Champagne Bronze

Hi Jeff, Thank you for your question. To remove the stopper you will need to unthread it from the flange. Best Regards, Courtney

Thank you for your question, Aquifers! The Delta Tub Drain Stopper and Flange RP31558CZ is designed to fit the standard drains. The waste plug flange is 1 1/2" and the waste plug threads are 5/16" -16 threads. We do not make a smaller or larger version of this model. We recommend checking with the tub manufacturer for their suggestions. Best regards, Tanya

Hi, Bryan! Thank you for your question. The Delta RP31556CZ Overflow Plate & Screws will match the Delta RP31558CZ Tub Drain. Here is a link to the part: https://www.deltafaucet.com/parts-product-detail?modelNumber=RP31556CZ Best Regards, Rosanna

Hi Sarah, Thank you for your question. The RP16686RB is the part number for the toe touch stopper only in the venetian bronze finish. http://www.deltafaucet.com/bath/details/rp16686rb.html?showPhotoGallery=false Thanks, Dave

Hi, Shay! Thank you for your question. The Delta RP31558CZ is designed to work with The RP693CZ bath waste assembly. Here are the technical specifications sheet for the unit to show the measurements for the unit: https://www.deltafaucet.com/parts-product-detail?modelNumber=RP693CZ Best Regards, Rosanna

I am having the same issue with mine. It will not close at all anymore.   It was installed in 2019

Hi, Naj, Thank you for your question! The RP31558CZ will work with the RP293 unit. Best Regards, Rosanna

Thank you for your question, Natalie! The Delta Toe operated Stopper assembly RP31558RB outer thread diameter of 1-1/2"-11. https://media.deltafaucet.com/SpecSheet/DSP-B-RP291_Rev_B.pdf Best regards, Tanya

This is the last delta anything I buy. Junk

Hello Pamela, Thank you for our inquiry! Yes, the RP16686 stopper assembly for the Delta Drain Assembly RP31558 can be purchased separately. https://www.deltafaucet.com/bathroom/product/RP16686 Best regards, Tanya

Hi Franky, Thank you for your question! Please click the link below to view the bath-waste installation. Refer to page 2 and 3 for help installing the drain, and page 5 for the parts diagram. http://www.deltafaucet.com/customersupport/documentation/rp43139.html?document=mi&fromDetailArea=repairparts&documentIndex=0#flashWrapper Best regards, Jon

Hi kpcsupport, Thank you for your question. Unfortunately we do not offer a twist and lock tub drain assembly any longer. We offer the toe touch and trip lever drain assemblies only. Thanks, Dave

Hi Sheryl, Thank you for your question! Below is a link to the technical specifications for the toe operated drain: http://www.deltafaucet.com/customersupport/documentation/rp293.html?document=ts&fromDetailArea=bath&documentIndex=0#flashWrapper Best regards, Brandis

Pjmo, Thank you for your question! This is the only toe-operated drain flange and stopper that we currently manufacture. Best regards, Jon

Hi, kkhamil! Thank you for your question. Although our finishes are extremely durable, they may be damaged by harsh abrasives or polish. To clean, we recommend simply wiping with a gentle damp cloth and then blotting dry with a soft towel. If water deposits are especially troublesome, you may use a 50/50 mixture of white vinegar and water to remove them. White vinegar is strong enough to dissolve mineral deposits, yet mild enough not to damage our finishes. Note: Please be aware white vinegar may stain some porous materials like untreated stone. If you have an unsealed tile or counter top, please take care when cleaning your products. If you’d prefer using a chemical cleaning product, our finishes may be cleaned with the following household cleaners: Formula 409® Antibacterial All-Purpose Cleaner, Fantastic® All-Purpose Cleaner, or Windex® Original Glass Cleaner, when used according to the manufacturer’ instructions. Any cleaners not listed above may be tried if they do not contain hydrofluoric, hydrochloric and/or phosphoric acids or similar caustic agents. Some examples of chemical cleaners to avoid are: green Scotch-Brite Heavy Duty Scrub Sponges, Scrubbing Bubbles Bathroom Cleaner and Lysol Basin Tub, and Soft Scrub and Tile Cleaner. Note: Any products that state on the label that they remove tarnish and rust will most likely harm the finished products. Most drain cleaners may be used when following their specific directions and not allowing exposure to the finish longer than 30 minutes. If you would like to further discuss the care of your unit, you may contact our residential warranty line directly at 800-345-3358 (prompt 2, then 4). We are available Monday through Friday 8a.m. to 8p.m. and Saturdays from 9a.m to 6p.m. Eastern Standard Time. Best Regards, Rosanna

Thank you for your question Hartmut! The Delta Tub Drain Stopper and Flange RP31558 is not designed to be taken apart, besides the stopper unscrewing out of the flange. Best Regards, Christina

Thank you for your question, Philip! The RP31558RB drain assembly has an outer diameter of 2.83" and an inner diameter of 1.60". Best regards, Edward

Hello Whking52, Than you for your question. The rubber gasket around the stopper assembly is not designed to be removed. The gasket helps seal and close off the drain, when trying to hold water in the tub. Best regards, Tanya

Hi Ken, Thank you for your question. The cap to the stopper and drain body for RP31558SS are brass with our (SS) brilliance stainless finish. They are not solid stainless steel. Thanks, Dave

Hi Milt, Thank you for your question. We do offer a waste and overflow that will work for your bathtub. We do not stock a unit that fits the deeper jacuzzi tubs. The drain assembly part # is RP391PB for the trip lever style that will fit your normal bathtub. Thanks, Dave

Hello jn7379, Thank you for your question! The outer diameter of the threads is 1 55/64". Best regards, Jon

Hello Eric60, Thank you for your inquiry! Yes, the stopper assembly of the RP31558RB, can be purchased separately. Below, I have provided the link for the stopper assembly RP16686RB. https://www.deltafaucet.com/parts-product-detail?modelNumber=RP16686RB Best regards, Tanya

Hi, Jaustin105! Thank you for your question. The RP31558 Drain Assembly has an outer diameter of 2.83" and an inner diameter of 1.60". Here is a link to the technical specifications sheet for the drain assembly this works for: https://media.deltafaucet.com/SpecSheet/dsp-b-rp293_A.pdf Best Regards, Rosanna

Hi, SIlver! Thank you for your question. The stopper for the RP31558RB drain assembly can be unscrewed counterclockwise to remove. Best Regards, Rosanna

Thank you for your question, James! The threads on the flange are 1 1/8" in length. Best regards, Jon

HI, Chris82! Thank you for your question. At this time, we do not make a tub drain assembly in the Matte Black Finish. We do apologize for any inconvenience this may cause. Best Regards, Rosanna

Hi Adam, Thank you for your question. The thread pattern on the flange of the RP31558SS tub drain is 1-1/2"-11. Thanks, Dave

Hi, Thank you for contacting us. We apologize for any inconvenience with your Delta Faucet Company product. I am also more than happy to have this opportunity to help you. The flange should screw out. Please contact us back if you have any questions or if you need further assistance you may call us at 1-800-345-3358. We are open Monday through Friday 7:00 AM to 7:00 PM central time, and 8:00 AM to 5:00 PM on Saturday. Thank you for your cooperation. Best Regards, Bethany

Thank you for your question, nancy476! Unfortunately, we do not manufacture anything to catch hair. Best Regards, Benjamin

Hello Sb57!. Thank you for your question. The stopper can be removed by unscrewing it counter-clockwise from the flange. If it seems stuck, it may help to use a flat rubber jar opener to help grip it. Thanks, Antoine