Single Handle Bathroom Faucet in Stainless

Hello Robert, Thank you for your question. The 564-SSMPU-DST single handle lavatory faucet is in the Brilliance Stainless Steel finish. Best regards, Brandis

Thank you for your question, canadian_remoob! The Delta Ashlyn collection does not have a standing tub filler option currently and we apologize for any inconvenience this may cause. The Delta Stryke free standing Floor Mount Tub Filler, model T47766-SSFL would be the closest stylistically. https://www.deltafaucet.com/bathroom/product/T47766-SSFL Best regards, Edward

Hi Chris, Thank you for your question. The spout on the model 564-SSMPU-DST measures 5-1/8" from the faucet center to the middle of the water stream. Here is a link to the spec sheet. http://www.deltafaucet.com/customersupport/documentation/564-ssmpu-dst.html?document=ts&fromDetailArea=bath&documentIndex=0#flashWrapper Thanks, Dave

Hi, Susie! Thank you for your question. The clearance to back splash for the Delta 564-SSMPU-DST Faucet should measure at a minimum of 2 1/2" (64 mm). Best Regards, Rosanna

Hi, Kren! Thank you for your question. The 564-SSMPU-DST will be the same exact make and quality where ever you choose to purchase the faucet at. The Lifetime Limited Warranty is the same regardless of where you choose to buy the faucet. Best Regards, Rosanna

Hi, PJW5! Thank you for your question, and I am sorry to hear that you are experiencing some issues with your Delta faucet. There is an adjustment to be able to make your faucet give hotter water. To do this, remove your handle and you will find the stem of the cartridge assembly. There is a switch on the cartridge located above the stem. Switch this to the left side. This will allow the hottest water. This will not adjust the flow for your hot water, however. For low flow at your hot side, we recommend to flush the supply lines for the flow issue. Over time, common water debris will settle in the house supply lines. Anytime the water is shut off to a portion of the home, this debris can become dislodged and will move through the pipes to be caught by a faucet. Local construction or the changing of the seasons can also cause this. Flushing the supply lines through the unit should remedy this situation. To flush the unit, we recommend the following: Start with the easy stuff: Remove your aerator, wand or hose to check the flow through the unit without that part installed. If the flow is good, the piece you’ve removed is where the issue is. Soaking the part in a 50/50 mixture of white vinegar and water could help remove any particles or debris blocking the flow. If the water does not have a good flow, the problem could be in the faucet. Next, check the supply lines for debris: Turn the supply off to both the hot and cold-water lines. Once off, turn the handle on the faucet to the on position and leave it there to bleed the lines of any excess water. Next, disconnect the hot water supply line and place it inside of a bucket. Once the line is securely positioned into the bucket, turn on the cold-water supply. Since the handle was left in the on position, the water will flow up the cold supply line, through the faucet cartridge and back down the hot water line into the bucket. Leave this flowing for at least 30 seconds. After flushing, reconnect the hot water line and repeat this process with the cold-water line to ensure all particles have been removed from both supplies. If you still have issues, please contact our Delta Customer Service line at (800)345-3358. We are available Monday-Friday, 7am-7pm, CST and Saturday, 8am-5pm, CST. You may also email at customerservice@deltafaucet.com. Best Regards, Rosanna

Hello, EML1! Thank you for your question. The tip of the handle is 8 1/8" above the deck surface in the on position. Please refer to the Technical Specifications for more information: https://media.deltafaucet.com/SpecSheet/dsp-l-564-mpu-dst_D.pdf Best regards, Jon

Hi RINDY, Thank you for your question. Unfortunately, we do not make another button for the handle. You can remove the button, however, we recommend to keep it in place as it will prevent buildup from forming around the set screw. Best regards, Jon