Monitor® 13 Series Shower Trim in Chrome

Dbrinton, Thank you for your question. For a slip-on installation, the pipe should extend 1-1/2" to 2-3/4” from the finished wall. Threaded installations require a 3-7/8" to 4” pipe. Best regards, Jon

Hi, Chris. Thank you for your question. We do not recommend welding the copper pipe inside the manifold for the Delta B114915C Tub and Shower Unit. We recommend reading the instructions before installing. Here is a link to the Maintenance & Installation Sheet for the faucet: https://media.deltafaucet.com/MandI/101650%20Rev%20B.pdf Best Regards, Rosanna

Hi, Phyllis! Thank you for your question. The Delta B114915C does include the RP70538 Valve Cartridge Assembly. Best Regards, Rosanna

Hi, Dominic! Thank you for your question. The shower arm for the Delta BT13210-SS Monitor Shower Faucet has 1/2 in. IPS male threads and fits a standard 1/2" connection. Best Regards, Rosanna

Hi, Chad! Thank you for your question. All of our Delta Shower Bath Trim Kits do include the needed valve cartridge assembly to install with the trim and valve body. Best Regards, Rosanna

Hello Jimmy Patel, Thank you for your question. Unfortunately, we do not have a video for adjusting the limit stop on the Delta Foundations Shower B114915C faucet model. However, to adjust the limit stop: First, remove the handle and adapter nut on the faucet and set them aside. You will now see a small black o-ring on the end of the brass stem. Remove this o-ring and again set aside. The next piece is the limit stop, you may see the words hot/cold. Rotate this part clockwise for hotter water. Each notch you move the piece, it will increase the maximum hot water by approximately 2-3 degrees. Reinstall the o-ring, adapter and handle. Please see page 7 of the instructions linked below. https://media.deltafaucet.com/MandI/88723%20Rev%20A.pdf Best regards, Tanya

Hello Brian White, Thank you for your question. Based on your description of the flow from the tub/shower, you are experiencing an issue known as shower rise. This is an installation issue, which has several possible causes: The valve could be upside down. The length from the valve to the tub spout is outside of the 8" to 18" rule. There is more than one 90-degree angle elbow. Something other than ½" smooth copper or galvanized pipe was used going to the spout. No push fittings. No "shark-bite" fittings. No cast or drop ear elbows. Something restricting the water flow to the spout, e.g. solder or something lodged in the pipe. If this is the cause of shower-rise it is possible to remove the blockage by removing the tub spout; then, feeding a plumber’s snake or a speedometer cable up through the tub drop. The act of feeding it causes it to twirl and loosen the blockage. Be sure to flush the valve before reinstalling the tub spout. Be sure to check the tub spout itself for blockage. Please feel free to call, email, or message us on social if there is anything else you need. Best regards, Tanya Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

Hi, Glenn! Thank you for your question. The Delta B114915C Tub and Shower Unit does not have an adjustment for water flow. The volume for the unit only comes on at full volume. Best Regards, Rosanna

Hi, Will! Thank you for your question. Here is a link to the Maintenance and Instruction Guide for the Delta B114915C Faucet to show how to adjust the rotational limit stop on page 7: https://media.deltafaucet.com/MandI/101650%20Rev%20B.pdf Best Regards, Rosanna

Hello Bryan, Thank you for your question! I am happy to help you! Our Delta 13/14 trim kits are interchangeable as long as the cartridge is the same. Our pre-2006 cartridge is RP19804 and post 2006 RP46074, I have included a link to both versions. If either one of these is your cartridge, you can upgrade to any new 13/14 trim kit. https://www.deltafaucet.com/parts/product/RP19804.html https://www.deltafaucet.com/parts/product/RP46074.html Please contact us back for any further questions. Best Regards, Nicole

Hi Mike, Thank you for contacting Delta Faucet Company! Please accept our sincere apology for the inconvenience you are experiencing. Here is what we can do to resolve your issue for you. Our Delta Faucet Foundations® Monitor® 13 Series Shower Trim In Chrome MODEL#: BT13210 uses the R10000-UNBX rough valve, this is our universal rough end valve that will work with all of our T13/14, T17, or 17T trim kits. I have included a link to the matte black trim kits we currently have available. https://www.deltafaucet.com/bathroom/showering/tub-and-shower-faucets?cgid2=Delta_Bathroom_Showering_Tub-and-Shower-Faucets&prefn1=finish&prefv1=Matte_Black&prefn2=narrowResults&prefv2=hideDiscontinued&prefn3=recertified&prefv3=false Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Nicole

Hello David! Thank you for your question and we are happy to help. We apologize for this information not being readily available to you. The Delta Foundations® Monitor® 13 Series Shower Trim In Chrome MODEL#: BT13210 does not have an option to lower the flow. With any further questions or concerns, please do not hesitate to reach out to us directly. Thank you for being a loyal Delta Faucet customer. Best Regards, Carrie

Hi Dan, thank you for your interest in the BT13210! Unfortunately, we only offer How To videos at the moment. Please refer to the link below if needed. https://www.youtube.com/c/deltafaucet/videos Please contact us directly if you have any questions or need additional assistance. Best Regards, Themar Digital Communications Specialist

Hi Enrico, thank you for your interest in the BT13210! Please refer to the parts diagram for any needed parts. https://media.deltafaucet.com/PartsDiagram/DPD-B-BT13010.pdf Please contact us directly if you have any questions or need additional assistance. Best Regards, Digital Communications Specialist

Hello SparkEE, Thank you for contacting Delta Faucet Company! I am sorry the flow is low on your Delta Faucet Foundations® Monitor® 13 Series Shower Trim In Chrome MODEL#: BT13210, and I am happy to help you! Low flow is caused by a blockage or debris, we would recommend flushing the shower unit. To flush the open valve without the cartridge, please follow the directions below. 1) Remove the handle by loosening the set screw on the side of the base of the handle. The set screw is either a 1/8" or 3/32" Allen screw. So you will need to use the appropriate size Allen wrench to loosen it. Loosen it just enough to be able to easily pull the handle off. * Note. If there is calcium build-up at the base of the handle, it may be necessary to soak it in a 50/50 solution of vinegar and water. Simply saturate the rag with the 50/50 solution, wrap it around the handle base and place a plastic bag over it. I would recommend do this the night before removing the handle. 2) After removing the handle, remove the trim sleeve. 3) Then you will need to remove the bonnet nut. The bonnet nut is the threaded ring at the valve opening. It unscrews counterclockwise. You will need a pipe wrench or a pair of channel locks. 4) After removing the bonnet nut, you will need to pull the cartridge straight out. You may need a small, skinny bladed screwdriver to wedge in between the lip of the cartridge and the valve to help start it out. 5) Once the cartridge is removed, you will have an open valve body. 6) Next, shut the shower door or curtain and turn the water on to the valve. Water should gush out, much like an open fire hydrant. Have someone observe if there is good water pressure coming out of the valve and let it flush for 30 seconds. 7) Re-install the cartridge and re-assemble in reverse of how it was disassembled. The Tub/Shower should then have a good flow. If it does not, the cartridge will need to be replaced. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Nicole

Hi Edgar, Thank you for contacting Delta Faucet. Please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Our Delta Faucet DELTA® Foundations® Monitor® 13 Series Shower Trim In Chrome MODEL#: BT13210 uses cartridge RP46074. This model is a one-handle unit that controls the temperature and the volume of water. Please see the parts breakdown in the link below. https://media.deltafaucet.com/PartsDiagram/BT13010_BT13210_BT13410_65593_Rev%20F.pdf Thank you for being a loyal Delta Faucet customer. Please feel free to call, email, or message us on social if you need anything else. Best Regards, Thema

Hi clay25, Thanks for your question regarding BT13210! This model utilizes a pressure-balancing cartridge; please check that both the hot and cold water valves are open equally. Please feel free to contact us with any questions or for further assistance. Best Regards, Emma Digital Communications Specialist

Hello Nicole, Thank you for your question about the Delta Faucet model BT13210 Foundations® Monitor® 13 Series Shower Trim In Chrome. I apologize for any difficulty finding this information. I know that can be frustrating. We are happy to help! See our selection of 2-port diverter trims here: https://www.deltafaucet.com/search-results?q=T118*&lang=en_US Or, see our 3-ports diverter trims here: https://www.deltafaucet.com/search-results?q=T119*&lang=en_US Please reach out at customerservice@deltafaucet.com or 1-800-345-DELTA if you have any questions or need additional assistance. Thank you for being a loyal Delta Faucet customer. Best regards, Bryan

Hi Cindy! Thank you for reaching out to us with your inquiry. We apologize for any issues you are having with the product and are happy to assist. This shower trim comes in a stainless finish, BT13210-SS, that is the closest we will have to nickel in this product. We appreciate your business and look forward to continually serving you. Best regards, Kelley

Hi mlb42, Thank you for your review regarding Delta Faucet BT13210! We apologize for any inconvenience you are experiencing and are happy to assist you. Yes, you can use H71 knob handle for the Delta Faucet BT13210. The valve will not need replaced. We appreciate your business and look forward to continuing to serve you. Thank you for being a loyal Delta customer. Best regards, Kyra Digital Engagement Specialist

Hi Daniel, Thank you for your question regarding our Delta Faucet B114915C. The H712 is not compatible with the B114915C trim kit. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hello Paul. I have sent you an email. If you need further information please contact us at 1-800-345-3358 or customerservice@deltafaucet.com. Best Regards Violet

Hi Larry, thank you for contacting Delta Faucet Company! Yes, the cartridge assembly included with our BT13410 will need to be adjusted to your preferred temperature. Please refer to page 12 box B in the link below. https://media.deltafaucet.com/MandI/107528%20Rev%20F.pdf We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Engagement Specialist

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. The max flow rate is 1.75 GPM @ 80 psi. Please feel free to contact us directly for technical or warranty information at 800-345-3358. We are available Monday through Friday from 8 a.m. to 8 p.m. and Saturdays from 9 a.m. to 6 p.m. Eastern Standard Time. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist

Hello Jimbo, Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available, and I am happy to help you! I have included the link below to our Delta Faucet Single Handle Tub And Shower In Stainless MODEL#: B114915C-SS parts diagram, this will provide you with part numbers for the individual parts. https://media.deltafaucet.com/PartsDiagram/DPD-B-B112915C_A.pdf Thank you for being a loyal Delta Faucet customer. Please contact us back with any further questions. Best Regards, Nicole

Hello Rocky, Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available for our DELTA Single Handle Tub And Shower MODEL#: B114915C, and I am happy to help you! I have included a link to our how-to video, on replacing the Delta Faucet shower cartridge. Please see the link below. https://www.youtube.com/watch?v=QGjEgAUHX8c&t=316s Thank you for being a loyal Delta Faucet customer. Please contact us back with any further questions. Best Regards, Nicole

Hello Carl, Thank you for your question! I am happy to assist you! The Delta B114915C shower cartridge rotational limit stop can be adjusted by removing the handle and trim sleeve. After removing them, the handle adapter and o-ring can be pulled off. From there, the blue limit stop can be pulled off and rotated counterclockwise to allow for hotter water. Once it has been rotated, the stop can then be placed back onto the cartridge and all additional components can be installed into place as well. Please contact us back with any further questions. Best Regards, Skyler

Hi Steve57, Thank you for your question about the Delta Faucet model BT13410. Please accept our apology for the inconvenience you are experiencing. We are happy to help! I first recommend removing the showerhead or tub spout. Flush the shower with full mix hot and cold with the showerhead or tub spout removed to clear trapped debris. The cartridge bonnet should be hand-tightened. The pressure balance valve needs both hot and cold water pressure to function correctly. Please reach out for further assistance or with any additional questions! Best Regards, Bryan

Hi Bruce, thank you for contacting Delta Faucet Company! We apologize for the issues you are experiencing! Please reach out to us directly so we can further assist you with this matter. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Communications Specialist