Single Handle Pull-Down Kitchen Faucet in Polished Nickel

Hello! This model uses the RP73000 cartridge. Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Dear Fcradit, Thank you for your question! If debris is trapped in the wand assembly, please remove the wand from the hose and try lightly tapping it upside-down on the counter. You may also try soaking it in a 50/50 white vinegar and water solution for about 15 minutes to help remove minerals. Best regards, Tanya

Hi, Kristen! Thank you for your question. Always blot dry any water from the faucet surface. Allowing water to evaporate on the surface can lead to build up of mineral deposits. Cleaning with a damp non-abrasive sponge and buffing it dry with a clean soft cloth should help keep your product looking beautiful. To remove water spots, use warm water and a soft, damp cloth. Hard water stains may be removed using a 50/50 solution of white vinegar and water. Make certain that you rinse the surface thoroughly with water afterward. If additional cleaning is required, all of our finishes may be cleaned with the following household cleaners: Formula 409® Antibacterial All Purpose Cleaner, Fantastik® All Purpose Cleaner, or Windex® Original Glass Cleaner, when used according to the manufacturers' instructions for use. Avoid using the following which can damage your finish: Avoid industrial cleaners and abrasive cleaners, such as those used for toilet bowls, green Scotch-Brite heavy duty scrub sponges, Scrubbing Bubbles Bathroom Cleaner and Lysol Basin Tub, Soft Scrub, and Tile Cleaner. Avoid products that state on the label that they remove tarnish and rust and those containing hydrofluoric, hydrochloric and/or phosphoric acids and caustic agents. Avoid harsh abrasives or polishes. Avoid bleach-based cleaners. Best Regards, Rosanna

Hi JD2020, Thank you for your question! The Delta Trinsic Pull-Down Kitchen 9159-DST faucet requires a 2 1/2" (64 mm) maximum deck thickness with the 10 1/2"escutcheon plate or a 3" (76 mm) maximum deck thickness without the 10 1/2" escutcheon plate. Please feel free to call, email, or message us on social if there is anything you need. https://media.deltafaucet.com/SpecSheet/DSP-K-9159-DST%20Rev%20F.pdf Best regards, Tanya Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

Thank you for your question, Jim. You can do this by removing the button cover on the bottom of the handle, then tightening the set screw with an 1/8" Allen wrench. Best regards, Jon

Thank you for your question, tania4444! I do apologize that you are not getting any water flow to your touch faucet, but will be more than happy to help! Model 9159T-DST runs on batteries, as a default option. When those batteries die, the light at the base of the faucet will blink red 3 times. Once the batteries die, the faucet will not be able to get water until new batteries are installed. Feel free to contact us directly, if you need further assistance. Best Regards, Benjamin

Hi, Susan! Thank you for your question. The Delta 9159-DST faucet handle can be tightened by first removing the red/blue temperature indicator. The set screw can be retightened with a 1/8" allen wrench. Best Regards, Rosanna

Hello Chapiz, Thank you for your inquiry! Yes, the Champagne Bronze finish on the Delta Trinsic Kitchen Pull-Down 9159-CZ-DST faucet, is a warm, muted gold finish. https://www.deltafaucet.com/service-parts/frequently-asked-questions/finish/primary-content-area/frequently-asked-questions/faq-item-2#answer-27987ea1-77e8-4eee-a9e2-f1fa8c0366fa Best regards, Tanya

Hello, Thank you for your question! The spout on this model features a total reach of 9 1/2". Please see the following link for more tech. spec. information. https://media.deltafaucet.com/SpecSheet/DSP-K-9159-DST%20Rev%20F.pdf Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Thank you for your question, Nancy! The faucet may be installed through the counter rather than the sink without purchasing additional parts. Please refer to the Technical Specifications to ensure that this faucet will work in your specific installation. https://media.deltafaucet.com/SpecSheet/DSP-K-9159-DST%20Rev%20E.pdf Best regards, Jon

No. I cannot understand why Delta approved this type of aeration in the first place. I constantly splash when trying to rince certain items and it is getting really annoying.

Hi, Colin! Thank you for your question. Here is a link for the warranty for our Delta faucets: https://www.deltafaucet.com/service-parts/warranty If you are experiencing an issue with your Delta faucet, please contact our Delta customer Service line at (800)345-3358. We are available Monday-Friday, 7am-7pm CST and Saturday, 8am-5pm, CST. Best Regards, Rosanna

Hi, Joha! Thank you for your question. The Delta 9159-CZ-DST Faucet sprayer assembly is non-metallic. Best Regards, Rosanna

Thank you for your question, Richard! The faucet is secured to the counter below with a mounting bracket that uses two screws and a nut. You will need to make sure these are tightened sufficiently, however please avoiding over tightening these parts. If you are using the optional three hole escutcheon plate, please make sure that this is also secure. If the counter is uneven, a small bead of silicone sealant may be used as well. Feel free to contact us directly if you need further assistance. https://media.deltafaucet.com/PartsDiagram/DPD-K-9159-DST%20Rev%20C.pdf Best regards, Edward

Hello Ernie, Thank you for your question! The Delta Trinsic Pull-Down Kitchen 9159-DST faucet can be installed as a single hole installation and a soap dispenser added for the second hole of the install. Please feel free to call, email, or message us on social if there is anything else you need. Best regards, Tanya Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

Thank you for your question. Delta Faucet model # 9159-CZ-DST weighs 6 pounds.

Hi, DPaul! Thank you for your question. The escutcheon plate is .45" thick. The 9159-DST faucet with the escutcheon plate is 15 11/16" and without the escutcheon plate it is 15 1/4". Best Regards, Rosanna

Hi Marion, Thank you for your question. Please check the thread size for the supply lines that the faucet will connect to. This faucet has 3/8" compression fittings. You may need adapters such as part number RP63263 which convert the threads to 1/2"-20 UN or 1/2"-14 NPSM. Best regards, Jon

Dear Tim, Thank you for your question. Yes, the Trinsic Pull-Down Kitchen 9159-CZ-DST faucet comes in the Brilliance Champagne Bronze. https://www.deltafaucet.com/kitchen/product/9159-CZ-DST https://www.deltafaucet.com/design-innovation/innovations/kitchen/brilliance-finishes Best regards, Tanya

Thank you for your question, mzack! The recommended clearance to the back splash is 1 1/2" (38mm) is measured from the center of the faucet or handle. https://media.deltafaucet.com/SpecSheet/DSP-K-9159-DST%20Rev%20E.pdf Best regards, Edward

Thank you for your interest in Delta Faucet Trinsic. The Bar/Prep model #9959-AR-DST has a spout total height of 13" . The Kitchen model #9159-AR-DST has a spout total height of 15 3/4". Attached is a video specifically created for the Trinsic series! http://www.deltafaucet.com/shopping-tools/research/video-gallery/video.html?v=4yfAL2DJQLk&cat=

Hi Kathy, Thank you for your question. When installed, the handle will be on the right side of the faucet. Best Regards, Courtney

We manufacture Delta faucets in our plant facilities in Greensburg, Indiana; Jackson, Tennessee; London, Ontario, CA (and Panyu, China). As a global manufacturer, we also source and assemble a number of parts around the world. No matter where in the world our products are sourced, manufactured or assembled, they are built to Delta Faucet Company’s exacting specifications and are quality tested to ensure long-lasting performance. The location information on the back of the box will tell you where your specific faucet model was made. Delta Faucet model 9159-AR-DST does not have to have the button held down for the sprayer to stay on.

Hi, craig1961! Thank you for your question, and I am sorry to hear that you are experiencing low flow from your Delta faucet. Over time, common water debris will settle in the house supply lines. Anytime the water is shut off to a portion of the home, this debris can become dislodged and will move through the pipes to be caught by a faucet. Local construction or the changing of the seasons can also cause this. Flushing the supply lines through the unit should remedy this situation. To flush the unit, we recommend the following: Start with the easy stuff: Remove your aerator, wand or hose to check the flow through the unit without that part installed. If the flow is good, the piece you’ve removed is where the issue is. Soaking the part in a 50/50 mixture of white vinegar and water could help remove any particles or debris blocking the flow. If the water does not have a good flow, the problem could be in the faucet. Next, check the supply lines for debris: Turn the supply off to both the hot and cold-water lines. Once off, turn the handle on the faucet to the on position and leave it there to bleed the lines of any excess water. Next, disconnect the hot water supply line and place it inside of a bucket. Once the line is securely positioned into the bucket, turn on the cold-water supply. Since the handle was left in the on position, the water will flow up the cold supply line, through the faucet cartridge and back down the hot water line into the bucket. Leave this flowing for at least 30 seconds. After flushing, reconnect the hot water line and repeat this process with the cold-water line to ensure all particles have been removed from both supplies. If this does not fix the issue, please contact us back. Best Regards, Rosanna

In addition to what you've already mentioned, I noticed that the valve names are different: The Trinsic uses the Diamond Seal Valve; the Trask uses the Euromotion Diamond Valve. Also, the handle styling is slightly different between the two (the Trinsic is skinnier.)

Hi Estana, Thank you for your question! The spout is 1 1/4" in diameter. Best regards, Jon

Hi, Laurie123! Thank you for your question. Please know that all of our products undergo rigorous tests to ensure long-lasting use and are made with high-grade materials. If you have any questions or need help, please feel free to contact our customer service department at 1-800-345-3358 or email us at customerservice@deltafaucet.com. Best Regards, Rosanna

Hi, Maddy! Thank you for your question. The Delta 9159-BL-DST Faucet, as well as all of our Diamond Seal Technology (DST) Faucets, are Lead-Free. Best Regards, Rosanna

Hello Akravenka, Thank you for your question! The Delta Trinsic Pull-Down kitchen 9159-AR-DST has a solid brass fabricated body. Best regards, Tanya

Hi, Thank you for contacting us. We apologize for any inconvenience with your Delta Faucet Company product. I am also more than happy to have this opportunity to help you. I see that you have already been assisted with this issue. If you need help with the installation of your order, please feel free to contact us back, as we would be happy to help. You can reach our customer service team at 1 800 345 3358, Monday through Friday from 7 am to 7 pm and Saturday 8 am to 5 pm CST. Best Regards, Bethany