Single Handle Pull-Down Bar / Prep Faucet with Touch₂O® Technology in Chrome

Hello Dave! Thank you for your question and we are happy to help. We apologize for this information not being readily available to you. For Lavatory Touch2O and Touch2O.xt faucets, the only way to make them manual is to remove the battery box from the solenoid while the water is running. For Kitchen Touch2O faucets, there are a few ways to make them manual. 1. If you can get the water to flow, then the most universal option can be used. It does not matter which model or version for this method (excluding Pascal & eFLow). With the faucet running water, disconnect the battery pack by opening it. Or if you have an open battery tray, remove the batteries. You now have a manually operated faucet. The solenoid was open allowing water to flow through and is now stuck open because you removed the power it would use to close. Reconnecting the battery would close the solenoid and make it electronic again. Or 2. If the faucet is a later generation, the solenoid assembly may be removed, and the wand hose connected directly to the valve outlet tube. a. Open the battery holder cap. b. Disconnect the sensor hook(s) from the spout and/or valve shank. c. Remove the hose clip and hose from the solenoid. d. Remove the solenoid from the valve outlet tube by removing the clip or swinging the clip open. e. Reconnect the hose with the hose clip to the spout outlet nipple. Note: If the solenoid uses an RP60520 adapter to connect to the valve outlet, for example, the early Trinsic, Addison, and Ashton … the pullout hose can be connected directly to the valve outlet nipple, not the adapter. a. Open the battery holder cap. b. Disconnect the sensor hook(s) from the spout and/or valve shank. c. Remove the hose clip and hose. d. Remove the metal solenoid clip and solenoid. e. Remove the adapter from the valve outlet tube. The adapter must also be removed to reveal the valve outlet nipple. The hose cannot connect to the adapter. f. Reconnect the hose with the hose clip to the valve outlet nipple. The faucet is now a manually operated pullout or pulldown. Or 3. If the solenoid Generation 1 or 2, and operational enough, we can directly energize it open. This is the least preferred method. These directions are in the M&Is, using the battery pack to reverse the power to the solenoid momentarily. Also attached below. This step can also be used on the solenoid for a Pascal if needed. With any further questions or concerns, please do not hesitate to reach out to us directly. Thank you for being a loyal Delta Faucet customer. Best Regards, Carrie

Hi Michele, Thanks so much for contacting Delta Faucet Company about the 9159T-KS-DST! I have included a link below to the Help Center, which will provide troubleshooting steps. https://support.deltafaucet.com/s/article/How-to-Troubleshoot-a-Delta-Kitchen-Faucet-with-Touch2O-Technology-1628025862981 Please contact us directly if you have any questions or need additional assistance. Best Regards, Nicole Digital Communications Specialist

Hi Dot16! Thank you for your question and we are happy to help. The magnet for the 9159T-DST is the RP80977. With any further questions or concerns, please do not hesitate to reach out to us again. Best Regards, Carrie

Hi ARelyea, Thanks so much for contacting Delta Faucet Company! We recommend cleaning Delta Faucet products with a 50/50 solution of white vinegar and water. If additional cleaning is required the following products are safe to use on all Delta Faucet finishes, when used according to the manufacturers’ instructions for use: Formula 409® Antibacterial All-Purpose Cleaner Fantastik® All-Purpose Cleaner Windex® Original Glass Cleaner Other gentle all-purpose or multi-surface cleaners may also be used. Please do not use anything labeled “all-purpose bathroom cleaner". Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. The faucet does not include a wrench. We recommend soaking the aerator in a 50/50 solution of white vinegar and water. Please feel free to contact us directly for technical information at 800-345-3358. We are available Monday through Friday from 8 a.m. to 8 p.m. and Saturdays from 9 a.m. to 6 p.m. Eastern Standard Time. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Please contact our TECH2O CONCIERGE at 1-844-923-5368 | Email: concierge@deltafaucet.com | Facebook/Twitter: @deltafaucet. We are open Monday through Friday 7:00 AM to 7:00 PM central time, and 8:00 AM to 5:00 PM on Saturday. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hi Alex, Thanks so much for contacting Delta Faucet Company! The 9959T-CZ-DST spout rotates 360 degrees which allows the handle to be installed on the front or left-hand side, however the handle rotation would be the same no matter where it is installed. Please contact us directly if you have any questions or need additional assistance. Best Regards, Nicole Digital Communications Specialist

Hi Ward617, Thanks for your question regarding 9159T-CZ-DST! No, the you can replace the magnet with RP80977. Please feel free to contact us with any questions or for further assistance. Best Regards, Emma Digital Communications Specialist

Hello Cathy, Thank you for your question! I am happy to help you! The easy way to make our Delta touch models manual including the 9159T-DST is to remove the battery box from the solenoid while the water is running. There are a couple more ways we can advise to make them manual, If the faucet is a later generation, the solenoid assembly may be removed, and the wand hose connected directly to the valve outlet tube. Lastly, If the solenoid Generation 1 or 2, and operational enough, we can directly energize it open. These directions are in the M&Is, using the battery pack to reverse the power to the solenoid momentarily. This is the least preferred method. Please contact us back for any further questions. Best Regards, Nicole

Hi Salil, Thank you for your question regarding our Delta Faucet 9159T-AR-DST. We have reached out to you directly. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hello sarahj! Thank you for your question! I will be happy to assist you! We have 2 beverage faucets available in the Champagne Bronze finish. 1977-CZ-DST and 1914-CZ-DST. Please refer to the link below. https://www.deltafaucet.com/kitchen/specialty-faucets/beverage?facetFinish=champagnebronze Feel free to contact us directly, if you need further assistance. Best Regards, Kyra

Hi Solenoid valve, Thank you for contacting Delta Faucet Company! We apologize for the issues you are experiencing and we are happy to help! We have reached out to you directly to further assist you with this matter. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Engagement Specialist

Hi Leanne, thank you for contacting Delta Faucet Company! No, there are no differences with our products at different stores. Delta products with the same model number will be the exact same no matter where they are purchased. Prices are set by dealers, so they can vary widely We appreciate your inquiry. Please reach out directly with further questions! Best Regards, Kyra Digital Communications Specialist

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Please contact our TECH2O CONCIERGE at 1-844-923-5368 | Email: concierge@deltafaucet.com | Facebook/Twitter: @deltafaucet. We are open Monday through Friday 7:00 AM to 7:00 PM central time, and 8:00 AM to 5:00 PM on Saturday. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist

Hi Donny202, Thank you for your question! Please accept our apology for the inconvenience you are experiencing. We are happy to help! There may be a small bit of debris on the sealing surface of the touch module. Flushing the waterway will likely clear the debris. See instructions here: https://support.deltafaucet.com/s/article/Touch2O-Drip Please reach out for further assistance or with any additional questions! Best Regards, Bryan

Hello Doug, Thank you for contacting us. I apologize for the leak when touched off you are experiencing with your Delta Faucet model 9159T DST Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology and I am happy to help you. The leak when off you are experiencing typically is caused by debris within the solenoid assembly. We recommend doing a flush on your electronic components. Please follow the below steps to resolve your drip: 1. Put the handle in the off position. 2. Remove the blue clip that is attached to the top of the solenoid assembly below the sink. 3. Pull the solenoid off of the faucet connection. Remove the debris screen in the top connection if able and clear any debris with tweezers or a q-tip. 4. Set a bucket under the pex supply line that is exposed. 5. Place the handle in the on position and allow it to run water for 2 full minutes. This will clear the supply line out of any debris. 6. Put the handle back into the off position. 7. Reconnect the solenoid to the faucet and clip it back into place. 8. Now remove the bottom clip from the solenoid where the hose connects and pull the hose off. 9. Turn the water back on for an additional 2 minutes to clear the solenoid assembly of any remaining debris. 10. Reconnect the hose and clip it into place again. Once that is finished, turn the water on to the faucet and run it for 15 seconds. Please contact us back directly via email with any further questions. Best Regards, Skyler

Hello, Kenneth! Thank you for contacting us at Delta Faucet! I apologize for this information not being available to you and I understand how frustrating that can be but I will be happy to help! Yes, we offer the Delta Faucet model 9959T-CZ-DST Trinsic® Single Handle Pull-Down Bar / Prep Faucet With Touch2O® Technology In Champagne Bronze. Please see the following link for more information. https://www.deltafaucet.com/kitchen/product/9959T-CZ-DST.html Please contact us directly if further assistance is needed at this time.  We appreciate your loyalty to Delta Faucet Company. Best Regards, Tim

Hello Jay13, Thank you for contacting us. I apologize you're having difficulties with your Delta touch faucet and I am happy to be able to assist you. There are some prominent reasons the touch feature could be acting erratically. Please make sure any wires are isolated from the solenoid box, the water supply lines, and anything else that might conduct electricity. If space is limited, we recommend a minimum of two inches of clearance, if possible. We also recommend placing the battery pack flat on the floor or as close to the ground at your feet as possible. The battery pack should have at least 2 inches of clearance from the walls or anything that can conduct electricity below the counter as the pack is also touch-sensitive. Please ensure your LED wire and green sense wire are isolated from anything conductive and your sense wire is securely mounted on the threads of the shank. After making the necessary changes, there is a certain way in which we recommend changing the batteries in order to allow the electronics to reset. First, remove the battery cable from the side of the battery box, then remove the old batteries and install new batteries, then reattach the battery cable. After doing this, turn the faucet on by the handle and tap the spout to turn it on and off by touch. If this resolves the issue we know it was battery-related. Please contact us back with any further questions. Best Regards, Skyler

Hello eszee! Thank you for your question and we are happy to help! The Deta 9195T-BL-DST has a light sensor on the base of the spout that blinks blue or red. There is no light that will turn on from the spout indicating when the water is running. With any further questions or concerns, please do not hesitate to reach out to us directly. Best Regards, Carrie

Hi KDEM, Thanks so much for contacting Delta Faucet Company! You can switch the TRINSIC® Pull-Down Kitchen Faucet MODEL#: 9159T-DST to a manual mode by turning the faucet on so that water is running and then remove the cap from the battery box.  Please reach out with further questions! Best Regards, Kelley Digital Communications Specialist

Hi LCJones629, thank you for your interest in the 9159T-CZ-DST! Always blot dry any water from the faucet surface. Allowing water to evaporate on the surface can lead to a build-up of mineral deposits. Cleaning with a damp non-abrasive sponge and buffing it dry with a clean, soft cloth should help keep your product looking beautiful. To remove water spots, use warm water and a soft, damp cloth. Hard water stains may be removed using a 50/50 solution of white vinegar and water. Make certain that you rinse the surface thoroughly with water afterward. I have also included a link to our “How to clean your faucet” on our website, please see the link below. https://www.deltafaucet.com/design-innovation/inspiredliving/how-to-clean-a-faucet Please contact us directly if you have any questions or need additional assistance. Best Regards, Digital Communications Specialist

Hi George, Thank you for your question about the Delta Faucet model 9159T-DST. Please accept our sincere apology for the inconvenience with the sprayer. We are happy to help! Unfortunately, the RP64069AR sprayer is only available with the included hose. Please reach out for further assistance or with any additional questions! Best Regards, Bryan Digital Communications Specialist

Good morning valued customer! Thank you for your question. We are happy to help you. Unfortunately, the arch of the Delta faucet 9959T-KS-DST is not replaceable. However, the bar prep faucet and the traditional faucet are the same size, except for the height and reach of the arch. Best Regards! Frank

Hello Nick, Thank you for your question! We apologize for the inconvenience you are experiencing and will be happy to help you. The Delta TRINSIC Single Handle Pull-Down Kitchen Faucet uses the cartridge assembly RP73000. Please feel free to contact us back for further assistance. Best Regards, Kelley

Hello, Marvin! Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available, and I am happy to help you! Our Delta Faucet DELTA® Trinsic® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology In Chrome MODEL#: 9159T-DST cartridge is part number RP73000. Please see the part in the link below. https://www.deltafaucet.com/parts/product/RP73000.html Thank you for being a loyal Delta customer. Please feel free to call, email, or message us on social if there is anything else you need. Best Regards, Themar

Hi Archer, Thank you for contacting Delta Faucet Company! Please accept our sincere apology for the inconvenience you are experiencing. Here is the information needed to resolve your issue for you. We would also like to have you do a flush of the unit, flushing the touch faucet will fix multiple issues with leaking, flow, and debris. Please see the steps below. We would like you to keep the handle in the center full-on position, then remove the wand. Hold the hose, so it does not fall back into the faucet, then point the hose into the sink. Next, I would like you to turn the faucet on by touch for 40 seconds. Then shut the faucet off by touch and back on for another 40 seconds. Then hold the handle and move it off and then back on without letting go for another 40 seconds. Once this has been done, please re-install the wand and check for leaking. Next, check the supply lines for debris: Turn the supply off to both the hot and cold-water lines. Once off, turn the handle on the faucet to the on position and leave it there to bleed the lines of any excess water. Next, disconnect the hot water supply line and place it inside a bucket. Once the line is securely positioned into the bucket, turn on the cold-water supply. If you have not already, please include your date of installation, full name, street address, city, state, zip code, and phone number for our reference. This allows us to more quickly resolve your issue. We appreciate your business and look forward to continuing to serve you. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Kelley

Hello JenL, Thank you for your question about the Delta Faucet model 9159T-CZ-DST TRINSIC® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology. I apologize for any difficulty finding this information. We are happy to help! The battery case should be located on the floor under the sink. Push the sides of the cap on the battery back to open the battery pack. This faucet can use 6 AA batteries or 6 C batteries. Please see the faucet manual for more information. https://media.deltafaucet.com/MandI/106559%20Rev%20D.pdf Please reach out directly at customerservice@deltafaucet.com or 1-800-345-DELTA if you have any questions or need additional assistance. Thank you for being a loyal Delta Faucet customer. Best regards, Bryan