Single Handle Pull-Down Kitchen Faucet with Touch₂O® Technology in Arctic Stainless

Hi bob27, Thanks for your question regarding 9159T-AR-DST! Yes, the cartridge can be replaced after removing the handle. For models produced after 1/1/2018, the cartridge is RP73000; however, for models produced before 1/1/2018, the cartridge is RP60114. You can purchase parts online or locally. Please see our Where to Buy page for help finding dealers in your area or online. Please contact us directly if you have any questions or need additional assistance. https://www.deltafaucet.com/where-to-buy Best Regards, Emma Digital Communications Specialist

Hi greggscott47, Thank you for your question about the Delta Faucet model 9159T-AR-DST. The RP6092 nuts for a three-hole installation measures at .43 outter diameter and thread count is .25-20UNC-1B with a thickness of .185. Please reach out for further assistance or with any additional questions! Best Regards, Bryan

Hello Anonymous, I am sorry that you faucet is not turning on. I have sent you and email to assist with this. For further assistance call us at 1-844-923-5368 or email us at concierge@deltafaucet.com. Best Regards Violet

Hello, Brad! Thank you for contacting us at Delta Faucet! I apologize for this information not being available to you but I will be happy to help! Thi Delta Faucet 9159T-AR-DST Trinsic Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology requires a hole size between 1 1/4" to 1 1/2". Please see the following technical specification sheet for more information. https://media.deltafaucet.com/SpecSheet/DSP-K-9159T-DST%20Rev%20G.pdf Please contact us directly if further assistance is needed at this time.  We appreciate your loyalty to Delta Faucet Company. Best Regards, Tim

Hi Curt, Thanks so much for contacting Delta Faucet Company about 9159T-AR-DST! We will need more information to better assist you. Please watch out for an email from customerservice@deltafaucet.com. Best Regards, Nicole Digital Communications Specialist

Hello Jbrent, Thank you for your question! We apologize for the low flow you are experiencing with your Delta faucet and I am happy to assist you! We thank you for being a loyal Delta Faucet customer. We do not recommend removing the flow restrictor from the Delta Faucet model 9159T-AR-DST Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology wand assembly and there is not a removable aerator. Reduced flow is typically caused by debris. If only one side is affected, there is debris in the supply line. To flush the supply line, first shut off the hot and cold water supply. Remove the hot supply line from the shut-off valve and place the line into a bucket. Open the handle to the middle position, fully open, then turn the cold supply back on for one minute. The cold water should flow through the faucet and out the hot supply tube. Reconnect the supply line and turn on both supplies. Check flow from the faucet. If this does not help, please let us know. Please contact us back directly via email with any further questions. Best Regards, Skyler

Hi Joel, Thank you for contacting Delta Faucet. Please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Our Delta Faucet Delta TRINSIC® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology In Arctic Stainless MODEL#: 9159T-AR-DST is not manufactured in Spot Shield Technology. Thank you for being a loyal Delta Faucet customer. Please feel free to call, email, or message us on social if you need anything else. Best Regards, Themar Digital Communications Specialist

Hello Doug, Thank you for reaching out to Delta Faucet Company! We apologize for the issues you are experiencing and we are happy to help! We have reached out to you directly to further assist you with this matter. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Engagement Specialist

Hi DomM, Thank you for your question about the Delta Faucet model 9159T-AR-DST. Please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue! A pull-out faucet may drip for a minute after being used as water is simply emptying from the aerator and hose of the faucet. If water debris is trapped inside the faucet, see here for troubleshooting instructions. https://support.deltafaucet.com/s/article/What-do-I-do-if-my-single-handle-kitchen-faucet-drips-from-the-spout-outlet-DST-model Please contact us directly if you have any questions or need additional assistance. We appreciate your business and look forward to continuing to serve you! Best Regards, Bryan Digital Communications Specialist

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Please contact our TECH2O CONCIERGE at 1-844-923-5368 | Email: concierge@deltafaucet.com | Facebook/Twitter: @deltafaucet. We are open Monday through Friday 7:00 AM to 7:00 PM central time, and 8:00 AM to 5:00 PM on Saturday. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Thank you for your question, Edwin! I have included a link to the technical specifications diagram for Delta Trinsic model 9159T-AR-DST, which will list the information you are looking for. https://media.deltafaucet.com/SpecSheet/DSP-K-9159T-DST%20Rev%20G.pdf Best Regards, Benjamin

Hello Mike, Thank you for contacting us, I would be happy to help you. Low flow is caused by blockage or debris, we recommend cleaning the bottom of the cartridge and puck with a soft cloth. Also we would recommend flushing, to flush the unit see the following. Start with the easy stuff: Remove your aerator, wand or hose to check the flow through the unit without that part installed. If the flow is good, the piece you’ve removed is where the issue is. Soaking the part in a 50/50 mixture of white vinegar and water could help remove any particles or debris blocking the flow. If the water does not have a good flow, the problem could be in the faucet. Next, check the supply lines for debris: Turn the supply off to both the hot and cold-water lines. Once off, turn the handle on the faucet to the on position and leave it there to bleed the lines of any excess water. Next, disconnect the hot water supply line and place it inside of a bucket. Once the line is securely positioned into the bucket, turn on the cold-water supply. Please contact us back if you have any questions or need further assistance. Best Regards, Nicole

Hi Salil, Thank you for your question regarding our Delta Faucet 9159T-AR-DST. We have reached out to you directly. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hello, Please accept our sincere apology for the inconvenience you are experiencing. We have reached out to you via email to further assist at this time. Best Regards, Tim Digital Communications Specialist

Hello, Marvin! Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available, and I am happy to help you! Our Delta Faucet DELTA® Trinsic® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology In Chrome MODEL#: 9159T-DST cartridge is part number RP73000. Please see the part in the link below. https://www.deltafaucet.com/parts/product/RP73000.html Thank you for being a loyal Delta customer. Please feel free to call, email, or message us on social if there is anything else you need. Best Regards, Themar

Hi, Cebd65! Thank you for your question. This unit is designed for a 3X 1 1/4" to 1 1/2" (32 mm to 38 mm) Hole Size. Please refer to the specification sheet. https://media.deltafaucet.com/SpecSheet/DSP-K-9159T-DST%20Rev%20G.pdf Best regards, Themar

Hi TAMI, Thank you for contacting Delta Faucet. Please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Our Delta Faucet Delta TRINSIC® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology In Arctic Stainless MODEL#: 9159T-AR-DST magnet replacement kit is MODEL#: RP80977. You can purchase parts online. To order parts over the phone, please call us at 1-800-345-DELTA (3358) Mon - Fri: 8 am - 7 pm EST Sat: 9 am - 6 pm EST. We accept Visa or MasterCard. Thank you for being a loyal Delta Faucet customer. Please feel free to call, email, or message us on social if you need anything else. Best Regards, Themar Digital Communications Specialist

Hi justine94, Thanks so much for contacting Delta Faucet Company about 9159T-AR-DST! Debris can cause the faucet to have low flow, we would recommend flushing the faucet and cleaning the debris screen. I have included a link below. https://support.deltafaucet.com/s/article/Why-does-my-faucet-have-low-water-pressure-1628028366405 Please contact us directly if you have any questions or need additional assistance. Best Regards, Nicole Digital Communications Specialist

Hello EricS, Thank you for your question! I am happy to help you! The low flow your experiencing with our Delta Faucet TRINSIC® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology MODEL#: 9159T-AR-DST appears to be caused by debris within the solenoid assembly. We recommend doing a flush on your electronic components. Please follow the below steps to resolve your drip: 1. Put the handle in the off position. 2. Remove the blue clip that is attached to the top of solenoid assembly below the sink. 3. Pull the solenoid off of the faucet connection. Remove the debris screen in the top connection if able and clear any debris with tweezers or a q-tip. 4. Set a bucket under the pex supply line that is exposed. 5. Place the handle in the on position and allow it to run water for 2 full minutes. This will clear the supply line out of any debris. 6. Put the handle back into the off position. 7. Reconnect the solenoid to the faucet and clip it back into place. 8. Now remove the bottom clip from the solenoid where the hose connects and pull the hose off. 9. Turn the water back on for an additional 2 minutes to clear the solenoid assembly of any remaining debris. 10. Reconnect the hose and clip it into place again. Once that is finished, turn the water on to the faucet and run it for 15 seconds. Thank you for being a loyal Delta customer. Please contact us back for any further questions. Best Regards, Nicole

Hi Felix, Thanks so much for contacting Delta Faucet Company about 9159T-AR-DST! The faucet has two solenoid options depending on what year it was manufactured. The hot water supply line will have the manufacturing date. If the faucet was installed before 2018, you would need EP74855. If the faucet was installed after 2018, you would need EP92546. I have included the parts diagram showing this information. https://media.deltafaucet.com/PartsDiagram/DPD-K-9159T-DST%20Rev%20I.pdf Please contact us directly if you have any questions or need additional assistance. Best Regards, Nicole Digital Communications Specialist

Hello! Thank you for contacting Delta Faucet Company! The aerator for our 9159T-AR-DST is the wand, RP64069AR. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Communications Specialist

Hi Ryan B, Thank you for contacting Delta Faucet Company! Please accept our sincere apology for the inconvenience you are experiencing with Delta Faucet Trinsic® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology In Arctic Stainless MODEL#: 9159T-AR-DST. Here is what we can do to resolve your issue for you. I would like to have you do a flush of the unit, flushing the touch faucet will fix multiple issues with leaking, flow, and debris. Please see the steps below. I would like you to keep the handle in the center full-on position, then remove the wand. Hold the hose, so it does not fall back into the faucet, then point the hose into the sink. Next, I would like you to turn the faucet on by touch for 40 seconds. Then shut the faucet off by touch and back on for another 40 seconds. Then hold the handle and move it off and then back on without letting go for another 40 seconds. Once this has been done, please re-install the wand and check for leaking. Next, check the supply lines for debris: Turn the supply off to both the hot and cold-water lines. Once off, turn the handle on the faucet to the on position and leave it there to bleed the lines of any excess water. Next, disconnect the hot water supply line and place it inside a bucket. Once the line is securely positioned into the bucket, turn on the cold-water supply. Next do this again with the hot supply, hook up both hot and cold supply and turn hot and cold valve open fully and equally. Once the faucet has been flushed, you should have flow again. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Nicole

Hello Valued Customer, Thank you for contacting Delta Faucet Company! When the A/C adapter is installed the faucet will use the power from the A/C adapter first, and if the A/C adapter is not working for any reason, the faucet will pull power from the batteries. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Communications Specialist

Hi Robbie, Thank you for reaching out to Delta Faucet Company! We apologize for the issues you are experiencing and we are happy to help! We have reached out to you directly to further assist you with this matter. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Engagement Specialist

Hi Valued Customer, Thank you for your question, please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Please feel free to contact us directly for warranty information at 800-345-3358. We are available Monday through Friday from 8 a.m. to 8 p.m. and Saturdays from 9 a.m. to 6 p.m. Eastern Standard Time. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hi Price! Thank you for your question and we are happy to help. We recommend flushing the valves of the Delta 9159T-AR-DST. With any further questions or concerns, please do not hesitate to reach out to us again. Best Regards, Carrie

Hello Will07, Thank you for contacting Delta Faucet Company. I am sorry to hear that your Trinsic® Single Handle Pull-Down Kitchen Faucet With Touch2O® Technology In Arctic Stainless MODEL#: 9159T-AR-DST is leaking when off, which can be very frustrating. I am so glad that you contacted us, so we can get this taken care of for you! I would like to have you do a flush of the unit, flushing the touch faucet will fix multiple issues with leaking, flow, and debris. Please see the steps below. I would like you to keep the handle in the center full-on position, then remove the wand. Hold the hose, so it does not fall back into the faucet, then point the hose into the sink. Next, I would like you to turn the faucet on by touch for 40 seconds. Then shut the faucet off by touch and back on for another 40 seconds. Then hold the handle and move it off and then back on without letting go for another 40 seconds. Once this has been done, please re-install the wand and check for leaking. Next, check the supply lines for debris: Turn the supply off to both the hot and cold-water lines. Once off, turn the handle on the faucet to the on position and leave it there to bleed the lines of any excess water. Next, disconnect the hot water supply line and place it inside a bucket. Once the line is securely positioned into the bucket, turn on the cold-water supply. If you have not already, please include your date of installation, full name, street address, city, state, zip code, and phone number for our reference. This allows us to more quickly resolve your issue. We appreciate your business and look forward to continuing to serve you. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Nicole